a5366 Allegro MicroSystems, Inc., a5366 Datasheet - Page 7
![no-image](/images/no-image-200.jpg)
a5366
Manufacturer Part Number
a5366
Description
Photoelectric Smoke Detector With Interconnect And Timer
Manufacturer
Allegro MicroSystems, Inc.
Datasheet
1.A5366.pdf
(13 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
a5366CA
Manufacturer:
HARRIS
Quantity:
6 227
Part Number:
a5366CA
Manufacturer:
ALLEGRO/雅丽高
Quantity:
20 000
Part Number:
a5366CLWT
Manufacturer:
ALLEGRO/雅丽高
Quantity:
20 000
A5366
C1 Pin
A capacitor connected to this pin determines the gain, A
the photoamplifier during the push-to-test mode and during the
chamber monitor test. A typical capacitor value for this high-
gain (supervisory) mode is 0.047 μF, but it should be selected
based on the photochamber background reflections reaching the
detector and the desired level of sensitivity. A
where C
should not exceed 0.1 μF. Coupling of other signals to the C1,
C2, and DETECT inputs must be minimized.
C2 Pin
A capacitor connected to this pin determines the gain, A
the photoamplifier during standby. A typical capacitor value for
this low-gain mode is 4700 pF, but it should be selected based
on a specific photochamber and the desired level of sensitiv-
ity to smoke. A
exceed 10,000 and thus C
increases by a nominal 10% after a local alarm is detected (three
consecutive detections). A resistor must be installed in series
with the C2 capacitor.
DETECT Pin
This is the input to the photoamplifier and is connected to the
cathode of the photodiode. The photodiode is operated at zero
bias and should have low dark leakage current and low capaci-
tance. A shunt resistor must be installed in parallel with the
photodiode.
STROBE Pin
This output provides a strobed, regulated voltage of V
The minus side of all internal and external photoamplifier cir-
cuitry is referenced to this pin.
VDD Pin
This pin is connected to the positive supply potential and can
range from 6 to 12 V with respect to V
IRED Pin
This output provides a pulsed base current for the external NPN
transistor, which drives the IR emitter. Its beta should be greater
than 100. To minimize noise impact, the IRED output is not
active when the horn and visible LED outputs are active.
I/O Pin
A connection at this pin allows multiple smoke detectors to be
interconnected. If any single unit detects smoke, its I/O pin is
1
is in pF. A
e
= 1 + (C
e
should not exceed 10,000 and thus C
2
/ 10), where C
2
should not exceed 0.1 μF. This gain
SS
2
.
is in pF. A
e
= 1 + (C
Pin and Circuit Description
e
should not
(In Typical Application)
DD
1
e
/ 10),
e
, of
, of
– 5 V.
1
Photoelectric Smoke Detector
driven high, and all connected units will sound their associated
horns. As an input, this pin is sampled every 128 clock cycles
(nominally 1.34 s) during standby. The LED is suppressed when
an alarm is signaled from an interconnected unit, and any local-
alarm condition causes this pin to be ignored as an input. An
internal NMOS device acts as a charge dump to aid in applica-
tions involving a large (distributed) capacitance, and is activated
at the end of a local or test alarm. This pin has an on-chip pull-
down device and must be left unconnected if not used. In the
application, there should be a series current-limiting resistor to
other smoke alarms.
HORN1, HORN2, and FEEDBACK Pins
These three pins are used with a self-resonating piezoelectric
transducer and horn-starting external passive components. The
output HORN1 is connected to the piezo metal support elec-
trode. The complementary output, HORN2, is connected to the
ceramic electrode. The FEEDBACK input is connected to the
feedback electrode. If the FEEDBACK pin is not used, it must
be connected to VSS.
LED Pin
This open-drain NMOS output is used to directly drive a visible
LED. The load for the low-battery test is applied to this output.
If an LED is not used, it should be replaced with an equivalent
resistor (typically 500 to 1000 Ω) such that the battery load-
ing remains about 10 mA. The low-battery test does not occur
coincident with any other test or alarm signal. The LED also
indicates detector status as follows (with component values as in
the typical application, all times nominal):
with Interconnect and Timer
Remote Alarm
Local Smoke
Timer Mode
Test Mode
Condition
Standby
115 Northeast Cutoff
1.508.853.5000; www.allegromicro.com
Allegro MicroSystems, Inc.
Worcester, Massachusetts 01615-0036 U.S.A.
Pulse Occurrence
Every 0.5 s
Every 0.5 s
Every 43 s
Every 10 s
No pulses
7