x96012 Intersil Corporation, x96012 Datasheet - Page 3

• Manufacturer Part Number: x96012
• Description: Universal Sensor Conditioner With Dual Look Up Table Memory And Dacs
• Manufacturer: Intersil Corporation

Electrical Specifications
Absolute Maximum Ratings
All Voltages are Referred to V
Temperature Under bias . . . . . . . . . . . . . . . . . . . . .-65°C to +100°C
Storage Temperature . . . . . . . . . . . . . . . . . . . . . . .-65°C to +150°C
Voltage on Every Pin Except VCC. . . . . . . . . . . . . . . . . -1.0V to +7V
Voltage on VCC Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0V to 5.5V
DC Output Current at Pin SDA . . . . . . . . . . . . . . . . . . 0mA to 5 mA
DC Output Current at Pins R1, R2, VREF and VSENSE
DC Output Current at Pins I1 and I2 . . . . . . . . . . -3.5mA to +3.5mA
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and
result in failures not covered by warranty.
NOTES:
.
Iccstby
Iccfull
Iccwrite
I
V
V
I
V
I
V
V
VRefout
RV
TCOref
VRef Range
TSenseRange
I
PLDN
INTTL
OHSDA
R
1. These parameters are periodically sampled and not 100% tested.
2. Parts are 100% tested at +25°C. Over-temperature limits established by characterization and are not production tested.
ILTTL
IHTTL
OLSDA
ILCMOS
IHCMOS
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.50mA to 1mA
REF
SYMBOL
Stand-by Current into V
Full Operation Current into V
Pin
Nonvolatile Write Current into
VCC Pin
On-chip Pull-down Current at WP,
A0, A1, and A2
SCL and SDA, Input Low Voltage
SCL and SDA, Input High Voltage
SCL and SDA Input Current
SDA Output Low Voltage
SDA Output High Current
WP, A0, A1, and A2 Input Low
Voltage
WP, A0, A1, and A2 Input High
Voltage
Output Voltage at V
VREF Pin Input Resistance
Temperature Coefficient of V
Output Voltage
Voltage Range when V
Input
Temperature Sensor Range
Current from pin R1 or R2 to VSS
SS
PARAMETER
3
Conditions are as follows, unless otherwise specified. All typical values are for T
Maximum and minimum specifications are over the recommended operating conditions. All voltages are
referred to the voltage at pin VSS. All bits in control registers are “0”. 255Ω, 0.1%, resistor connected between
R
external 2kΩ resistor. 2-wire interface in “standby” (see Notes 8 and 9 on page 5). WP, A0, A1, and A2 floating.
V
REF
1
and VSS, and another between R
pin unloaded.
REF
REF
CC
at +25°C
Pin
is an
REF
CC
R
2-wire interface reading from
memory, I
DAC input bytes: FFh, V
Average from START condition until t
after the STOP condition
WP: V
unloaded.
V(WP), V(A0), V(A1), and V(A2) from 0V
to V
Pin voltage between 0 and V
as an input.
I(SDA) = 2mA
V(SDA) = V
-20µA ≤ I(V
VRM bit = “1”, +25°C
Notes 1 and 7
Note 5
Note 1
1
and R
CC
CC
, R
2
1
X96012
TEST CONDITIONS
floating, V
and I
REF
CC
1
and R
) ≤ 20µA
2
2
and V
both connected to V
2
REF
Thermal Information
Pb-free reflow profile . . . . . . . . . . . . . . . . . . . . . . . . . .see link below
Operating Conditions
Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . .-40°C to +100°C
Temperature While Writing to Memory . . . . . . . . . . . . 0°C to +70°C
Voltage on VCC Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3V to 5.5V
Voltage on any other Pin . . . . . . . . . . . . . . . . . . . . . . . . VCC ± 0.3V
Floating, V
SS
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
REF
. 400kHz TTL input at SCL. SDA pulled to V
unloaded.
CC
unloaded.
, and SDA
REF
WP
SS
,
0.8 x VCC
(Note 2)
1.205
-100
MIN
2.0
-40
20
-1
0
0
0
0
1
0
A
TYP
1.21
= +25°C and 5V at pin V
4
1
0.2 x VCC
(Note 2)
CC
1.215
MAX
+100
VCC
3200
100
100
0.8
0.4
1.3
15
20
10
40
through an
2
November 19, 2007
ppm/°C
FN8216.2
UNIT
mA
mA
mA
µA
µA
µA
kΩ
µA
°C
V
V
V
V
V
V
V
CC
.