v23809-f7-c10 Infineon Technologies Corporation, v23809-f7-c10 Datasheet - Page 3

• Manufacturer Part Number: v23809-f7-c10
• Description: Multimode 1300 Nm Led Fibre Channel 266 Mbd Transceiver*
• Manufacturer: Infineon Technologies Corporation

Transmitter Electro-Optical Characteristics
(Values in brackets are for 320 MBd)
Notes
1. Measured at the end of 5 meters of 62.5/125/0.275 graded index
2. The input data pattern is a 12.5 MHz square wave pattern.
3. Center wavelength is defined as the midpoint between the two
4. Spectral width (full width, half max.) is defined as the difference
5. 10% to 90% levels. Measured using a 12.5 MHz square wave pat-
6. Extinction ratio is defined as PL/PH x 100%. Measurement system
7 . Test method and consideration as in FC-PH Appendix A.
8. Measured with the K28.5 pattern from Chapter II of the FC-PH
9. Measured with the K28.7 pattern from Chapter II of the FC-PH
Fiber Optics
Transmitter
Data Rate
Launched Power
(Average)
into 62.5 m Fiber
Center Wavelength
Spectral Width
(FWHM)
Output Rise Time,
10%–90%
Output Rise Time,
10%–90%
Temperature Coefficient
of Optical Output Power
Extinction Ratio
(Dynamic)
Deterministic Jitter
Random Jitter
fiber using calibrated power meter and a precision test ferrule.
Cladding modes are removed. Values valid for EOL.
50% levels of the optical spectrum of the LED.
between 50% levels of the optical spectrum of the LED.
tern with an optoelectronic measurement system (detector and
oscilloscope) with 3 dB bandwidth ranging from less than 0.1 MHz
to more than 750 MHz.
as in Note 5.
at 266MBd.
which equals a 133 MHz square wave.
(2, 4)
(1, 2)
(2, 6)
(5)
(5)
(7, 9)
(7, 8)
(2, 3)
Symbol Min. Typ.
DR
P
t
t
TCp
ER
t
t
R
F
DJ
RJ
C
O
l
0
–20
(–21)
1280
0.6
–16
(–17)
Max. Units
266
(320)
–14
1380 nm
200
2.0
(2.5)
2.2
(2.5)
.03
12
16
9
mBaud
dBm
ns
dB/ C
%
3
Receiver Electro-Optical Characteristics
(Values in brackets are for 320 MBd)
Notes
1. Pattern: Manchester coding / NRZI (no scrambling)
2. For a bit error rate (BER) of less than 1x10E-12 over a receiver eye
3. For a BER of less than 1x10E-12. Measured in the center of the eye
4. Test method and considerations as in FH-PC Appendix A.
5. Measured with the K28.5 pattern from Chapter II of the FC-PH at
6. Measured with the K28.7 pattern from Chapter II of the FC-PH
7 . An increase in optical power through the specified level will cause
8. A decrease in optical power through the specified level will cause
9. PECL compatible. Load is 50
Receiver
Data Rate
Sensitivity
(Average Power)
Saturation
(Average Power)
Deterministic
Jitter
Random Jitter
Signal Detect
Assert Level
Signal Detect
Deassert Level
Signal Detect
Hysteresis
Output Low
Voltage
Output High
Voltage
Output Data Rise/Fall
Time, 20%–80%
Output SD Rise/Fall
Time, 20%–80%
opening of least 1.0ns. Measured with a 2
opening with a 2
266 MBd.
which equals a 133 MHz square wave.
the Signal Detect output to switch from a Low state to a High state.
the Signal Detect output to switch from a High state to a Low state.
conditions. For dynamic measurements a tolerance of 50 mV should
be added for V
V23809-F7-C10, Multimode 1300 nm LED Fibre Channel 266 MBd Transceiver
(4, 5)
(9)
(9)
(7)
(4, 6)
(8)
CC
(2)
(3)
7
=5 V.
–1 PRBS.
Symbol
DR
P
P
t
t
P
P
P
P
V
V
t
DJ
RJ
R
IN
SAT
SDA
SDD
SDA
SDD
OL
OH
, t
–V
F
–V
–
CC
CC
into V
Min.
5
–14
–43.5
–45
1.5
–1810
–1025
(1)
CC
–2 V. Measured under DC
7
–1 PRBS.
Typ.
–30
–11
266
(320)
–26
19
9
–30.5
1.3
40
Max.
–29
–1620 mV
–880
Units
mBaud
dBm
%
dBm
dB
ns