v23809-j307-c13 Infineon Technologies Corporation, v23809-j307-c13 Datasheet - Page 3

• Manufacturer Part Number: v23809-j307-c13
• Description: Ac/dc Coupled Multimode 1.0625 Fibre Channel 1x9transceiver
• Manufacturer: Infineon Technologies Corporation

Receiver Electro-Optical Characteristics
Notes
1 For a BER of less than 1 x 10E–12. Measured with a 2
2. An increase in optical power above the specified level will cause the
3. A decrease in optical power below the specified level will cause the
4. PECL compatible. Load is 50
Pin Description 1x9 Pin Row
Semiconductor Group
Receiver
Sensitivity
(Average Power)
Saturation
(Average Power)
Signal Detect
Assert Level
Signal Detect
Deassert Level
Signal Detect
Hysteresis
Signal Detect
Assert Time
Signal Detect
Deassert Time
Output Low Voltage
Output High Voltage
Output Data Rise/Fall
Time, 20%–80%
Pin Name
RxV
RD
RDn
SD
RxV
TxV
TDn
TD
TxV
Case
ER=9 dB.
SIGNAL DETECT output to switch from a Low state to a High state.
SIGNAL DETECT to change from a High state to a Low state.
conditions. For dynamic measurements a tolerance of 50 mV should
be added. V CC =5 V.
CC
EE
EE
CC
Rx Ground
Rx Output
Data
Rx Output
Data
RX Signal
Detect
Rx +5 V
Tx +5 V
Tx Input Data PECL
Tx Input Data PECL
Tx Ground
Ground
(2)
(3)
(1)
(4)
(4)
Level
Power
Supply
PECL
Output
PECL
Output
PECL
Output
active
high
Power
Supply
Power
Supply
Input
Input
Power
Supply
Power
Supply
Symbol Min.
P
P
P
P
P
P
t
t
V
V
V
V
t
ASS
DAS
R
IN
SAT
SDA
SDD
SDA
SDD
OL
CC
OH
CC
,
t
–
F
–
–
into V
Pin # Description
1
2
3
4
5
6
7
8
9
S1/2
0
–30
–1950
–1025
CC
–2 V. Measured under DC
Negative power supply,
normally ground
Receiver output data
Inverted receiver
output data
A high level on this
output shows that there
is an optical signal
Positive power supply,
+5 V
Positive power supply,
+5 V
Inverted transmitter
input data
Transmitter input data
Negative power supply,
normally ground
Support stud (floating)
Typ.
–19
–24
–27
3
Max.
–16
–20
100
350
–1600
–720
400
7
–1 PRBS and
Units
dBm
dB
mV
ps
s
3
LASER SAFETY
This laser transceiver is a Class 1 laser product. It complies with
IEC 825-1 and FDA 21 CFR 1040.10 and 1040.11. The transceiver
must be operated under recommended operating conditions.
Caution
The use of optical instruments with this product will
increase eye hazard!
General Restrictions
Classification is valid only if the module is operated within the
specified temperature and voltage limits. The system using the
module must provide power supply protection that guarantees
that the system power source will cease to provide power if the
maximum recommended operation limit or more is detected on
the +5 V at the power source. The case temperature of the
module must be in the temperature range given in the recom-
mended operating limits. These limits guarantee the laser safety.
Usage Restrictions
The optical ports of the modules shall be terminated with an opti-
cal connector or with a dust plug.
Note
Failure to adhere to the above restrictions could result in a modification
that is considered an act of “manufacturing, ” and will require, under
law, recertification of the modified product with the U.S. Food and Drug
Administration (ref. 21 CFR 1040.10 (i)).
Laser Data
Required Labels
Laser Emission
V23809-J307-C10/C13, AC/DC Multimode 850 nm 1.0625 GBd FC 1x9 Transceiver
Wavelength
Total output power (as defined by IEC: 50 mm
aperture at 10 cm distance)
Total output power (as defined by FDA: 7 mm
aperture at 20 cm distance)
Beam divergence
Indication of laser
aperture and beam
Complies with 21 CFR
1040.10 and 1040.11
FDA
Class 1 Laser Product
IEC
850 nm
<400 W
<70 W
12