sy88053al Micrel Semiconductor, sy88053al Datasheet
sy88053al
Available stocks
Related parts for sy88053al
sy88053al Summary of contents
Page 1
... An external voltage applied at the VTHP pin on the SY88053AL will move the crossing point up and down, from 20% to 80%, to achieve the best BER. ...
Page 2
... Typical Application Circuit Fixed Decision Threshold Ordering Information Part Number Package Type SY88053ALMG MLF-16 (1) SY88053ALMGTR MLF16 Note: 1. Tape and Reel. Pin Configuration May 2010 Programmable Decision Threshold Operating Package Marking Range Industrial 053A with Pb-Free bar line indicator Industrial 053A with Pb-Free bar line indicator ® ...
Page 3
... Device ground. Exposed pad must be soldered (or equivalent) to the Ground same potential as the ground pins. Positive power supply. Bypass with 0.1µF||0.01µF low ESR capacitors. Power Supply 0.01µF capacitors should be as close as possible to VCC pins. 3 SY88053AL Pin Function . LVL sets the CC M9999-052610-A hbwhelp@micrel ...
Page 4
Absolute Maximum Ratings Supply Voltage (V ) ....................................... 0V to +4.0V CC Input Voltage (DIN, /DIN) ............(V Output Current (I ) ............................................... ±25mA OUT EN Voltage ............................................................. LOS Voltage.......................................... V LVL Lead Temperature (soldering, 20sec.) ..................... 260°C Storage ...
Page 5
AC Electrical Characteristics V = 3.0 to 3.6V 50Ω Load CC Symbol Parameter Output Rise/Fall Time (20% to 80%) Deterministic t JITTER Random V Differential Input Voltage Swing ID V ...
Page 6
Typical Functional Characteristics V = 3.3V 25°C, V tied THN May 2010 , R = 50Ω -2V, unless otherwise stated. THREF M9999-052610- hbwhelp@micrel.com or (408) 955-1690 A ...
Page 7
Typical Operating Characteristics V = 3.3V 25° 50Ω LOS Assert/De-Assert Levels 100 10 1 0.1 1 LOSLVL Resistor (KOhm) May 2010 -2V, unless otherwise stated 100 Crosspoint Adjustment 85 ...
Page 8
... Signal Crossing Adjustment In order to optimize the BER of the optical link where the noise is unevenly distributed between the high and the low levels, the SY88053AL provides two pins for output signal crossing control. The output crossing can be adjusted by connecting pins VTHN and VTHREF together while applying a DC voltage at VTHP pin ...
Page 9
Functional Block Diagram May 2010 9 hbwhelp@micrel.com M9999-052610 (408) 955-1690 ...
Page 10
Figure 2. Input Structure Figure 4. LOS Output Structure May 2010 Figure 1. V and V Definition IS ID Figure 3. Output Structure Figure 5. LOS Note: Recommended value for R 10 Setting Circuit LVL is 15kΩ or less. LOSLVL ...
Page 11
Related Product and Support Documentation Part Number Function AN-45 Notes on Sensitivity and Hysteresis in Micrel Post Amplifiers May 2010 Data Sheet Link http://www.micrel.com/product- info/app_hints+notes.shtml 11 hbwhelp@micrel.com M9999-052610-A or (408) 955-1690 ...
Page 12
Package Information MICREL, INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131 USA TEL +1 (408) 944-0800 FAX +1 (408) 474-1000 WEB The information furnished by Micrel in this data sheet is believed to be accurate and reliable. However, no responsibility ...