ad840sq Analog Devices, Inc., ad840sq Datasheet - Page 3

• Manufacturer Part Number: ad840sq
• Description: Wideband, Fast Settling Op Amp
• Manufacturer: Analog Devices, Inc.

REV. C
NOTES
1
2
3
4
All min and max specifications are guaranteed. Specifications shown in boldface are tested on all production units.
Specifications subject to change without notice.
ABSOLUTE MAXIMUM RATINGS
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Internal Power Dissipation
Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . V
Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . .
Storage Temperature Range
Junction Temperature (T
Lead Temperature Range (Soldering 60 sec) . . . . . . . . +300 C
NOTES
1
2
Recommended Heat Sink:
Input offset voltage specifications are guaranteed after 5 minutes at T
Full power bandwidth = slew rate/2
Refer to Figures 22 and 23.
“S” grade T
permanent damage to the device. This is a stress rating only, and functional
operation of the device at these or any other conditions above those indicated in
the operational section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect device reliability.
+175 C at an ambient temperature of +25 C.
Stresses above those listed under “Absolute Maximum Ratings” may cause
Maximum internal power dissipation is specified so that T
Thermal Characteristics:
Cerdip Package
Plastic Package
LCC Package
Plastic (N) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.5 W
Cerdip (Q) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.3 W
LCC (E) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.0 W
Q, E . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .–65 C to +150 C
N . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .–65 C to +125 C
Aavid Engineering© #602B
MIN
Models
AD840JN
AD840KN
AD840JQ
AD840KQ
AD840SQ
AD840SQ-883B
5962-89640012A
AD840SE-883B
5962-8964001CA
NOTES
1
2
2
J and S Grade Chips also available.
N = Plastic DIP; Q = Cerdip; E = LCC (Leadless
Ceramic Chip Carrier).
–T
MAX
30 C/W
30 C/W
35 C/W
specifications are tested with automatic test equipment at T
JC
ORDERING GUIDE
J
) . . . . . . . . . . . . . . . . . . . . . +175 C
2
V
PEAK
110 C/W
100 C/T
150 C/W
JA
Package Options
N-14
N-14
Q-14
Q-14
Q-14
Q-14
Q-14
E-20A
E-20A
.
1
Derate at
8.7 mW/ C
10 mW/ C
6.7 mW/ C
J
does not exceed
2
A
= +25 C.
18 V
6 V
S
–3–
A
= –55 C and T
A
= +125 C.
METALIZATION PHOTOGRAPH
Dimensions shown in inches and (mm).
AD840 Connection Diagrams
Contact factory for latest dimensions.
Plastic DIP (N) Package
Cerdip (Q) Package
LCC (E) Package
and
AD840