ad8321 Analog Devices, Inc., ad8321 Datasheet - Page 8
![no-image](/images/no-image-200.jpg)
ad8321
Manufacturer Part Number
ad8321
Description
Gain Programmable Catv Line Driver
Manufacturer
Analog Devices, Inc.
Datasheet
1.AD8321.pdf
(20 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ad8321AR
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Part Number:
ad8321AR-REEL
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Part Number:
ad8321ARZ
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Part Number:
ad8321XR3
Manufacturer:
ADI/亚德诺
Quantity:
20 000
AD8321
The attenuation setting in the AD8321 is determined by the
8-bit word in the data latch. The SDATA load sequence is
initiated by a falling edge on DATEN. The gain control data
(SDATA) is serially loaded (MSB first) into the 7-bit shift register
at each rising edge of the clock. See Figure 24. While DATEN
is low, the data latch holds the previous data word allowing the
attenuation level to remain unchanged. After eight clock cycles
the new data word is fully loaded and DATEN is switched high.
This enables the data latch and the loaded register data is passed to
the attenuator with the updated gain value. Also at this DATEN
transition, the internal clock is disabled, thus inhibiting new
serial input data.
The power amplifier has two basic modes of operation. A for
ward mode (or power-up mode) and a reverse mode (or power-
down) mode. In the power-up mode (PD = 1), the power
amplifier stage is enabled and the AD8321 has a maximum gain
of 20 V/V or 26 dB (into 75 W). With a total attenuation of
53.43 dB in the DAC, vernier and preamp, the AD8321’s total
gain range is 26 dB to –27.43 dB. In both the forward or reverse
mode the single-ended output signal maintains a dc level of
V
linearity.
In the power-down mode (PD = 0), the power amplifier is
turned off and a “reverse” amplifier (the inner triangle in Figure
22) is enabled. During this 1-to-0 transition, the output power
is disabled. This assures that S11 and S22 remain approximately
equal to zero thus minimizing line reflections. In the time domain,
as PD switches states, a transitional glitch and pedestal offset
results (See Figures 14 and 15). These anomalies have been
minimized by temperature compensated internal circuitry and
laser trimming. The powered down supply current drops to 52 mA
versus 90 mA in the power-up mode.
CC
/2. This dc output level provides for optimum large signal
ANALOG
OUTPUT
SDATA
DATEN
CLK
PD
SIGNAL AMPLITUDE (p-p)
T
ES
VALID DATA WORD G1
8 CLOCK CYCLES
T
Figure 24. Serial Interface Timing
DS
MSB. . . .LSB
T
C
T
T
WH
EH
GAIN TRANSFER (G1)
T
GS
–8–
APPLICATIONS
General Application
The AD8321 is primarily intended for use as the return path
(also called upstream path) Power Amplifier (PA) or line driver
in cable modem applications. Upstream data is modulated in
either QPSK or QAM format. This is done either in DSP or by
a dedicated QPSK/QAM modulator such as the AD9853 or
other modem/modulator chip. The amplifier receives its input
signal either from the dedicated QPSK/QAM modulator or from
a DAC. In both cases, the signal must be low-pass filtered
before being applied to the line driving amplifier. Because the
distance to the central office varies from cable modem sub
scriber to subscriber, resulting in various line losses, signals from
various subscribers will require attenuation while others may
require gain. As a result, the AD8321 line driver is required to
vary its output applying attenuation or gain as needed so that all
signals arriving at the central office are of the same amplitude.
DOCSIS (Data Over Cable Service Interface Specifications)
requires a cable modem output signal ranging in power from a
minimum of 8 dBmV to a maximum of 58 dBmV. In cable
modem applications where DOCSIS compliance is desired, the
AD8321 amplifier must be used in conjunction with a 75 W
matching attenuator connected between the AD8321 output
and the low-pass input port of the diplexer. See the schematic in
Figure 28. The matching attenuator is used to achieve DOCSIS-
compliant noise levels at the lower end of the AD8321 output
power range. The insertion loss of a diplexer is typically less
than 1 dB. As a result of these combined losses, the PA line
driver must be capable of delivering sufficient power into a 75 W
load while maintaining reasonable distortion performance at the
output of the modem. (See sections containing “DOCSIS” for
further information. All references to DOCSIS pertain to
SP-RFI-I04-980724 entitled Radio Frequency Interface
Specification.)
T
OFF
VALID DATA WORD G2
PEDESTAL
GAIN TRANSFER (G2)
T
ON
REV. A