lmk042bj103zc-f Taiyo Yuden Co., Ltd, lmk042bj103zc-f Datasheet - Page 29

• Manufacturer Part Number: lmk042bj103zc-f
• Description: High Value Multilayer Ceramic Capacitors
• Manufacturer: Taiyo Yuden Co., Ltd

【Test Methods and Remarks】
【Test Methods and Remarks】
【Test Methods and Remarks】
【Test Methods and Remarks】
【Test Methods and Remarks】
■
＊ This catalog contains the typical specification only due to the limitation of space. When you consider purchase of our products, please check our specification.
mlcc06_reli_e-01
12． Resistance to Soldering
Specified Value
13． Temperature Cycle （ Thermal Shock）
Specified Value
Preconditioning:Thermal treatment （at 150℃ for 1hr） Note1
Conditions for 1 cycle／ Step 1: Minimum operating temperature
14． Humidity （ Steady state）
Specified Value
15． Humidity Loading
Specified Value
16． High Temperature Loading
Specified Value
Note1
Note2
Note3
Preconditioning:Thermal treatment （at 150℃ for 1hr） Note1
Solder temperature:270±5℃
Duration:3±0.5sec.
Preheating conditions: 80 to 100℃, 2 to 5 min.
Recovery : 24±2hrs under the standard condition
Number of cycles:5 times
Recovery : 24±2hrs under the standard condition
Preconditioning:Thermal treatment （at 150℃ for 1hr） Note1
Temperature:40±2℃
Humidity：90 to 95%RH
Duration: 500
Recovery : 24±2hrs under the standard condition
According to JIS 5102 clause 9.9.
Preconditioning:Voltage treatment
Temperature:40±2℃
Humidity：90 to 95%RH
Applied voltage:Rated voltage
Charge/discharge current：50mA max.
Duration: 500
Recovery : 24±2hrs under the standard condition
According to JIS 5102 clause 9.10.
Preconditioning:Voltage treatment
Temperature:125±3℃ （B7） , 85±2℃ （BJ）
Applied voltage:Rated voltage×2 （ HMK）
Charge/discharge current：50mA max.
Duration: 1000
Recovery : 24±2hrs under the standard condition
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
RELIABILITY DATA
Thermal treatment : Initial value shall be measured after test sample is heat-treated at 150＋0/−10℃ for an hour and kept at room temperature for 24±2hours.
Voltage treatment : Initial value shall be measured after test sample is voltage-treated for an hour at both the temperature and voltage specified in the test conditions, and
Standard condition: Temperature: 5 to 35℃, Relative humidity: 45 to 85 % RH, Air pressure: 86 to 106kPa
＋24
−0
＋24
−0
＋24
−0
Rated voltage×1.5 （ QMK）
Rated voltage×1.2 （ SMK）
hrs
hrs
hrs
150 to 200℃, 2 to 5min.
Step 2: Room temperature
Step 3: Maximum operating temperature
Step 4: Room temperature
kept at room temperature for 24±2hours.
When there are questions concerning measurement results, in order to provide correlation data, the test shall be conducted under the following condi-
tion.
Temperature: 20±2℃,
Unless otherwise specified, all the tests are conducted under the "standard condition".
Note2
Note2
Note3
Note3
Note3
Note3
Note3
Relative humidity: 60 to 70 % RH, Air pressure: 86 to 106kPa
Appearance:
Capacitance change:
Dissipation factor :
Insulation resistance:
Withstanding voltage （ between terminals） : No abnormality
Appearance:
Capacitance change: Within±15% （HMK） , ±7.5% （QMK, SMK）
Dissipation factor:
Insulation resistance: Initial value
Appearance:
Capacitance change: Within±15%
Dissipation factor :
Insulation resistance: 25MΩ μF or 1000MΩ, whichever is smaller.
Appearance:
Capacitance change: Within±15%
Dissipation factor:
Insulation resistance: 10MΩ μF or 500MΩ, whichever is smaller.
Appearance:
Capacitance change: Within±15%
Dissipation factor:
Insulation resistance: 50MΩ μF or 1000MΩ, whichever is smaller.
＋0
−3
＋0
−3
℃ 30±3min.
℃ 30±3min.
2 to 3min.
2 to 3min.
No abnormality
7%max （ HMK） , 5%max （ QMK, SMK） .
No abnormality
Initial value
No abnormality
7%max （ HMK） , 5%max （ QMK, SMK） .
No abnormality
7%max （ HMK） , 5%max （ QMK, SMK） .
1
No abnormality
Within±15% （HMK） , ±10% （QMK, SMK）
Initial value
Initial value
mlcc06_reli-R2