mc10xs3535 Freescale Semiconductor, Inc, mc10xs3535 Datasheet
mc10xs3535
Available stocks
Related parts for mc10xs3535
mc10xs3535 Summary of contents
Page 1
... Watchdog FLASHER OUT2 IGN RST OUT3 CLOCK OUT4 CS FOG OUT5 S0 FETIN SI SCLK FETOUT CSNS GND Document Number: MC10XS3535 Rev. 2.0, 7/2010 10XS3535 HIGH SIDE SWITCH Bottom View PNASUFFIX 98ART10511D 24-PIN PQFN PB FREE ORDERING INFORMATION Temperature Device Package Range ( -40 °C to 125 °C ...
Page 2
INTERNAL BLOCK DIAGRAM VCC Vcc failure detection SCLK R DWN CLOCK LIMP FOG FLASHER IGN RST R DWN Over-temperature Prewarning CSNS Figure 2. 10XS3535 Simplified Internal Block Diagram 10XS353 2 INTERNAL BLOCK DIAGRAM VBAT OV/UV/POR ...
Page 3
CP GND OUT5 Figure 3. 10XS3535 Pin Connections (Transparent Top View Of Package) Table 1. 10XS3535 Pin Definitions A functional description of each pin can be found in the Functional Pin Description section beginning on Pin Pin Name Pin Function ...
Page 4
PIN CONNECTIONS Table 1. 10XS3535 Pin Definitions (continued) A functional description of each pin can be found in the Functional Pin Description section beginning on Pin Pin Name Pin Function Number Master-Out Slave Input 11 VCC Power 12 ...
Page 5
Table 2. Maximum Ratings All voltages are with respect to ground unless otherwise noted. Exceeding these ratings may cause a malfunction or permanent damage to the device. Ratings ELECTRICAL RATINGS Overvoltage Test Range (all OUT[1:5] ON with nominal DC current) ...
Page 6
ELECTRICAL CHARACTERISTICS STATIC ELECTRICAL CHARACTERISTICS STATIC ELECTRICAL CHARACTERISTICS Table 3. Static Electrical Characteristics Characteristics noted under conditions 3.0 V ≤ V otherwise noted. Typical values noted reflect the approximate parameter means at T otherwise noted. Characteristic POWER INPUTS (VBAT, VCC) ...
Page 7
Table 3. Static Electrical Characteristics (continued) Characteristics noted under conditions 3.0 V ≤ V otherwise noted. Typical values noted reflect the approximate parameter means at T otherwise noted. Characteristic LOGIC INPUT/OUTPUT (IGN, CS, CSNS) (CONTINUED) CSNS Tri-state Leakage Current VCC ...
Page 8
ELECTRICAL CHARACTERISTICS STATIC ELECTRICAL CHARACTERISTICS Table 3. Static Electrical Characteristics (continued) Characteristics noted under conditions 3.0 V ≤ V otherwise noted. Typical values noted reflect the approximate parameter means at T otherwise noted. Characteristic PARKING LIGHT OUT1 Output Drain-to-Source ON ...
Page 9
Table 3. Static Electrical Characteristics (continued) Characteristics noted under conditions 3.0 V ≤ V otherwise noted. Typical values noted reflect the approximate parameter means at T otherwise noted. Characteristic PARKING LIGHT OUT1 (CONTINUED) High Over-current Shutdown Threshold 2 Low Over-current ...
Page 10
ELECTRICAL CHARACTERISTICS STATIC ELECTRICAL CHARACTERISTICS Table 3. Static Electrical Characteristics (continued) Characteristics noted under conditions 3.0 V ≤ V otherwise noted. Typical values noted reflect the approximate parameter means at T otherwise noted. Characteristic HIGH BEAM OUT3 Output Drain-to-Source ON ...
Page 11
Table 3. Static Electrical Characteristics (continued) Characteristics noted under conditions 3.0 V ≤ V otherwise noted. Typical values noted reflect the approximate parameter means at T otherwise noted. Characteristic FOG LIGHT OUT4 Output Drain-to-Source ON Resistance (I OUT = V ...
Page 12
ELECTRICAL CHARACTERISTICS STATIC ELECTRICAL CHARACTERISTICS Table 3. Static Electrical Characteristics (continued) Characteristics noted under conditions 3.0 V ≤ V otherwise noted. Typical values noted reflect the approximate parameter means at T otherwise noted. Characteristic FLASHER OUT5 (CONTINUED) High Over-current Shutdown ...
Page 13
DYNAMIC ELECTRICAL CHARACTERISTICS Table 4. Dynamic Electrical Characteristics Characteristics noted under conditions 3.0V ≤ V otherwise noted. Typical values noted reflect the approximate parameter means at T otherwise noted. Characteristic POWER OUTPUTS TIMING (OUT1 TO OUT5) Current Sense Valid Time ...
Page 14
ELECTRICAL CHARACTERISTICS DYNAMIC ELECTRICAL CHARACTERISTICS Table 4. Dynamic Electrical Characteristics Characteristics noted under conditions 3.0V ≤ V otherwise noted. Typical values noted reflect the approximate parameter means at T otherwise noted. Characteristic POWER OUTPUTS TIMING (OUT1 TO OUT5) (CONTINUED) t ...
Page 15
Table 4. Dynamic Electrical Characteristics Characteristics noted under conditions 3.0V ≤ V otherwise noted. Typical values noted reflect the approximate parameter means at T otherwise noted. Characteristic WATCHDOG TIMING Watchdog Timeout (SPI Failure) I/O PLAUSIBILITY CHECK TIMING Fault Shutdown Delay ...
Page 16
ELECTRICAL CHARACTERISTICS DYNAMIC ELECTRICAL CHARACTERISTICS Table 4. Dynamic Electrical Characteristics Characteristics noted under conditions 3.0V ≤ V otherwise noted. Typical values noted reflect the approximate parameter means at T otherwise noted. Characteristic SPI INTERFACE CHARACTERISTICS Maximum Frequency of SPI Operation ...
Page 17
TwRSTB t ENBL TENBL CSB CS 10% V 0.7VDD CC t Tlead LEAD 90 0.7VDD SCLK SCLK 10 0.2VDD 90% V 0.7 VDD Don’t Care SI SI 10% V 0.2VDD Figure 4. Input Timing Switching Characteristics ...
Page 18
ELECTRICAL CHARACTERISTICS TIMING DIAGRAMS CS High logic level Low logic level V OUT[1:5] V PWR V OUT[1:5] 70% V PWR 30% V PWR CS High logic level Low logic level I OUT[1:5] I MAX t DLY(ON) I CSNS t CSNS(VAL) ...
Page 19
The 10XS3535 is designed for low-voltage automotive and industrial lighting applications. Its five low R (three 10 mΩ and two 35 mΩ) can control the high sides of SUPPLY VOLTAGE (VBAT) The VBAT pin of the 10XS3535 is the power ...
Page 20
FUNCTIONAL DESCRIPTION FUNCTIONAL PIN DESCRIPTION IGNITION INPUT (IGN) The ignition input wakes the device. It also controls the Fail mode activation. The signal is “high active”, meaning the component is active in case of a logic high at the input. ...
Page 21
CSB CS SCLK SI D15 D14 D13 D12 SO OD15 OD14 OD13 OD12 Notes NOTES: 1. RSTB logic H state during the above operation. 1. D15 : D0 relate to the most recent ordered entry of data ...
Page 22
FUNCTIONAL DEVICE OPERATION OPERATIONAL MODES FUNCTIONAL DEVICE OPERATION SLEEP MODE The Sleep mode is the default mode of the 10XS3535. This is the state of the device after first applying battery voltage (V ) and prior to any I/O transitions. ...
Page 23
AUTORESTART STRATEGY The autorestart circuitry is used to supervise the outputs and reactivate high side switches in cases of overload or under-voltage failure conditions, to provide a high availability of the outputs. Autorestart feature is available in Fail mode when ...
Page 24
FUNCTIONAL DEVICE OPERATION OPERATIONAL MODES POWER OFF MODE The 10XS3535 is in Power OFF mode when the battery voltage is below V thresholds. For more details, BATPOR[1,2] please refer to Loss of VBAT paragraph. (wake=0) (wake=1) and (fail= ...
Page 25
IGN IGN_ON Deglitcher Flasher_ON FLASHER Deglitcher Fog_ON FOG Deglitcher RST UVF external external_ON external: IGN, FLASHER, FOG external_ON: IGN_ON, FLASHER_ON, FOG_ON Analog Integrated Circuit Device Data Freescale Semiconductor VBAT Wake-up bar VBAT Internal regulator Dig2.5V Fault management VCC fail OR ...
Page 26
FUNCTIONAL DEVICE OPERATION LOGIC COMMANDS AND REGISTERS SERIAL INPUT COMMUNICATION SPI communication compliant to 3.3 V and 5 accomplished using 16-bit messages. A message is transmitted by the master starting with the MSB, D15, and ending with the ...
Page 27
ADDRESS 00000 — INITIALIZATION The Initialization register is used to read the various statuses, choose one of the six outputs current recopy, load the H7 bulbs profile for OUT2 only, enable the FOG pin and synchronize the switching phases between ...
Page 28
FUNCTIONAL DEVICE OPERATION LOGIC COMMANDS AND REGISTERS Table 9. Switching Phases 10 11 Bit D7 at logic [1] turns ON OUT1. OUT1 is turned OFF with bit D7 at logic [0]. This register allows the master to control the duty ...
Page 29
Device UVF OTW Status Output UVF OTW Status Reset Don’t care PREVIOUS ADDRESS SOA[1: the previous two LSBs are 00, bits OD15 ...
Page 30
FUNCTIONAL DEVICE OPERATION LOGIC COMMANDS AND REGISTERS OD13 (UVF) = Under-voltage Flag on Vbat OD12 (OTW) = Over-temperature Prewarning Flag OD11 (OTS) = Over-temperature Flag for all outputs OD10 (NM) = Normal mode OD8 (Overvoltage) = Over-voltage Flag on Vbat ...
Page 31
PROTECTION AND DIAGNOSIS FEATURES OUTPUT PROTECTION FEATURES The 10XS3535 provides the following protection features: •Protection against transients on V BAT ISO 7637) •Active clamp, including protection against negative transients on output line •Over-temperature •Severe and resistive Over-current •Open Load during ...
Page 32
FUNCTIONAL DEVICE OPERATION PROTECTION AND DIAGNOSIS FEATURES VBAT with an inductive VBAT line. The maximum VBAT voltage is limited active clamp circuitry BATCLAMP through the load. In case of open load condition, the positive (OCHI2 = 1) ...
Page 33
OFF out: OFF OCHI1 autorestart = 0 out: external ( ( and (external_on = 1) (external_ON = 0) external external_ON external: IGN, FLASHER, FOG external_ON: IGN_ON, Flasher_ON, ...
Page 34
FUNCTIONAL DEVICE OPERATION PROTECTION AND DIAGNOSIS FEATURES The current recopy feature for OUT1:5 is disabled during a high over-current shutdown phase (t 2 during low over-current shutdown thresholds. The current recopy output delivers current only during ON time of the ...
Page 35
EXTERNAL PIN STATUS The 10XS3535 provides the status of the FLASHER, FOG, and IGN pins via the SPI in real time and in Normal mode. FAILURE HANDLING STRATEGY A highly sophisticated failure handling strategy enables light functionality even in case ...
Page 36
FUNCTIONAL DEVICE OPERATION PROTECTION AND DIAGNOSIS FEATURES WD Bit D10 0 75ms window watchdog 10XS353 36 1 timeout 75ms window watchdog Figure 18. Watchdog window 0 D10 is toggled after the window watchdog Fail Mode activation Analog Integrated Circuit Device ...
Page 37
Figure 19 below shows full vehicle light functionality, including fog lights, battery redundancy concept, light substitution mode, and Fail mode. CP 100nF 10XS3535 VBAT CornerLight Switch (Front Left) VCC 100nF CP 35XS3500 VBAT CornerLight Switch (Rear Left) VCC V BAT ...
Page 38
PACKAGING PACKAGING DIMENSIONS For the most current package revision, visit www.freescale.com and perform a keyword search using the “98A” listed below. 10XS353 38 PACKAGING PACKAGING DIMENSIONS PNA SUFFIX 24-PIN PQFN 98ART10511D ISSUE 0 Analog Integrated Circuit Device Data Freescale Semiconductor ...
Page 39
Analog Integrated Circuit Device Data Freescale Semiconductor PNA SUFFIX 24-PIN PQFN 98ART10511D ISSUE 0 PACKAGING PACKAGING DIMENSIONS 10XS3535 39 ...
Page 40
PACKAGING PACKAGING DIMENSIONS 10XS353 40 PNA SUFFIX 24-PIN PQFN 98ART10511D ISSUE 0 Analog Integrated Circuit Device Data Freescale Semiconductor ...
Page 41
Analog Integrated Circuit Device Data Freescale Semiconductor PNA SUFFIX 24-PIN PQFN 98ART10511D ISSUE 0 PACKAGING PACKAGING DIMENSIONS 10XS3535 41 ...
Page 42
... REVISION HISTORY Revision Date Description of Changes 5/2010 • Initial Release 1.0 • Changed PN to MC10XS3535PNA 7/2010 2.0 • Changed classification to Advance Information 10XS353 42 REVISION HISTORY Analog Integrated Circuit Device Data Freescale Semiconductor ...
Page 43
... Freescale Semiconductor was negligent regarding the design or manufacture of the part. Freescale™ and the Freescale logo are trademarks of Freescale Semiconductor, Inc. All other product or service names are the property of their respective owners. © Freescale Semiconductor, Inc. 2010. All rights reserved. MC10XS3535 Rev. 2.0 7/2010 ...