fmce-0828 Interpoint Corp., fmce-0828 Datasheet
fmce-0828
Related parts for fmce-0828
fmce-0828 Summary of contents
Page 1
... Where low noise currents are required to meet CE03 of MIL-STD-461C and/or CE102 of ML-STD-461D, E and F, a power line filter is needed. The FMCE-0828 EMI power line filters reduce the common mode and differential noise generated by the converters. FMCE-0828 filters reduce input ripple current by 60 dB, typical, at 500 kHz and 1 MHz when used in conjunction with Interpoint’ ...
Page 2
... Weight (maximum) • 60 grams cases F5 and J6 • 86 grams typical case U screening The FMCE-0828 EMI Input filter offers Standard, /ES or 883, Class H, QML screening. See Screening Tables 1 and 2 for more informa- tion. EMI FILTER DC/DC CONVERTER +Vin +Vin ...
Page 3
... Volt input – 8 aMp pin out DoWn-leaDeD MoDel 1 pin out siDe-leaDeD MoDel Angled corner and cover marking indicate pin one. Page FMCE-0828 Rev E - 20100427 Crane Aerospace & Electronics Power Solutions Squared corner and dot on top of package indicate pin one BOTTOM VIEW FMCE-0828 See case F5 and J6 for dimensions ...
Page 4
... From eaCh Category to Determine the moDel number – _______ case/leaD option (non-FlangeD, DoWn-leaDeD leave blank) F (down-leaded flanged) sl (case u, side-leaded) Page FMCE-0828 Rev E - 20100427 Crane Aerospace & Electronics Power Solutions Dscc nuMBers DsCC D (5915) FmCe-0828 rawing s P imilar ...
Page 5
... 25° 125°c c Page FMCE-0828 Rev E - 20100427 Crane Aerospace & Electronics Power Solutions FMCE-0828 MIN TYP MAX unIts -0 VDC -0.5 — — — ...
Page 6
... MFL28 converters with an FMCE-0828 IguRe 1.25 26 100 Page FMCE-0828 Rev E - 20100427 Crane Aerospace & Electronics Power Solutions MIL-STD-461C POWER IN LIMITS NARROWBAND FREQUENCY (MHz) CE03: Three paralleled and synchronized MFL28 converters with an FMCE-0828 IguRe FREQUENCY (kHz) FMCE-0828 Attenuation F 9 IguRe 100 ...
Page 7
... FMce-0828 eMi input Filters – cases Seam Seal Case dimensions in inches (mm) Tolerance ±0.005 (0.13) for three decimal places CAUTION Heat from reflow or wave soldering may damage the device. Solder pins individually with heat application not exceeding 300°C for 10 seconds per pin. ...
Page 8
... FMce-0828 eMi input Filters – cases Flanged cases: Designator "F" required in Case Option position of model number. Seam Seal Case dimensions in inches (mm) Tolerance ±0.005 (0.13) for three decimal places ±0.01 (0.3) for two decimal places unless otherwise specified CAUTION Heat from reflow or wave soldering may damage the device. Solder pins individually with heat application not exceeding 300° ...
Page 9
... FMce-0828 eMi input Filters – cases Angled corner indicates pin one. 1.505 (38.23) max. 1.380 (35.05) 1.250 (31.75) 1.050 (26.67) 0.850 (21.59) 0.650 (16.51) 0.450 (11.43) 0.250 (6.35) 0.120 (3.05) 0.000 www.interpoint.com 28 Volt input – 8 aMp TOP VIEW CASE U* Side-leaded case *Designator “SL” required in Case Option position of model number ...
Page 10
... E RODUCT LEMENT standard and /es nOn-Qml 2 M/S yes cReenIng able leMent Page FMCE-0828 Rev E - 20100427 Crane Aerospace & Electronics Power Solutions /883 (C H, QML) LASS VALUATION /883 1 Class h Qml M yes yes no yes yes N/A yes ...
Page 11
... FMCE-0828 EMI Input Filters, FMCE-0828 Rev E - 20100427. This revision supersedes all previous releases. All technical information is believed to be accurate, but no responsibility is assumed for errors or omissions. Interpoint reserves the right to make changes in products or specifications without notice. FMCE-0828 EMI Filters are a trademark of Interpoint. Copyright © 1999 - 2010 Interpoint Corporation. All rights reserved. www. interpoint.com FMce-0828 eMi input Filters 28 Volt input – ...