ltc4069edc-4.4 Linear Technology Corporation, ltc4069edc-4.4 Datasheet - Page 6
![no-image](/images/manufacturer_photos/0/3/389/linear_technology_corporation_sml.jpg)
ltc4069edc-4.4
Manufacturer Part Number
ltc4069edc-4.4
Description
Standalone 750ma Li-ion Battery Charger In 2 ? 2 Dfn With Ntc Thermistor Input
Manufacturer
Linear Technology Corporation
Datasheet
1.LTC4069EDC-4.4.pdf
(16 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LTC4069EDC-4.4
Manufacturer:
LT
Quantity:
10 000
Company:
Part Number:
ltc4069edc-4.4#PBF
Manufacturer:
LT
Quantity:
5 000
PI FU CTIO S
LTC4069-4.4
GND (Pin 1): Ground.
CHRG (Pin 2): Open-Drain Charge Status Output. The
charge status indicator pin has three states: pull-down,
pulse at 2Hz and high impedance state. This output can be
used as a logic interface or as an LED driver. When the
battery is being charged, the CHRG pin is pulled low by an
internal N-channel MOSFET. The pin becomes high im-
pedance when any of the following conditions occur: the
charge current drops below 10% of full-scale current, the
timer ends, or the charger is shut down. If the battery
voltage remains below 2.9V for one quarter of the charge
time, the battery is considered defective and the CHRG pin
pulses at a frequency of 2Hz (75% duty cycle). When the
NTC pin voltage rises above 0.76 • V
• V
duty cycle).
BAT (Pin 3): Charge Current Output. Provides charge
current to the battery and regulates the final float voltage
to 4.4V. An internal precision resistor divider on this pin
sets the float voltage and is disconnected in shutdown
mode.
V
provides power to the charger. V
to 5.5V. This pin should be bypassed with at least a 1µF
capacitor. When V
voltage, the LTC4069-4.4 enters shutdown mode, drop-
ping I
6
CC
U
CC
(Pin 4): Positive Input Supply Voltage. This pin
, the CHRG pin pulses at a frequency of 2Hz (25%
BAT
to about 1µA.
U
CC
U
is within 30mV of the BAT pin
CC
CC
can range from 3.75V
or drops below 0.35
NTC (Pin 5): Input to the NTC (Negative Temperature
Coefficient) Thermistor Temperature Monitoring Circuit.
Under normal operation, connect a thermistor from the
NTC pin to ground and a resistor of equal value from the
NTC pin to V
0.35 • V
cold, charging is suspended, the internal timer is frozen
and the CHRG pin output will start to pulse at 2Hz. Pulling
this pin below 0.016 • V
is approximately 3°C of temperature hysteresis associ-
ated with each of the input comparator’s thresholds.
PROG (Pin 6): Charge Current Program and Charge Cur-
rent Monitor Pin. Connecting a 1% resistor, R
ground programs the charge current. When charging in
constant-current mode, this pin servos to 1V. In all modes,
the voltage on this pin can be used to measure the charge
current using the following formula:
Floating the PROG pin puts the charger in shutdown mode.
In shutdown mode, the LTC4069-4.4 has less than 20µA
supply current and about 1µA battery drain current.
Exposed Pad (Pin 7): Ground. The Exposed Pad must be
soldered to the PCB ground to provide both electrical con-
tact and rated thermal performance.
I
BAT
CC
=
R
at hot temperatures or rises above 0.76 • V
V
PROG
PROG
CC
. When the voltage at this pin drops below
• 1000
CC
disables the NTC feature. There
PROG
406944f
CC
, to
at