c450tr3547m-0217 Cree, Inc., c450tr3547m-0217 Datasheet - Page 2
![no-image](/images/no-image-200.jpg)
c450tr3547m-0217
Manufacturer Part Number
c450tr3547m-0217
Description
Tr3547m™ Leds
Manufacturer
Cree, Inc.
Datasheet
1.C450TR3547M-0217.pdf
(5 pages)
Notes:
1. Maximum ratings are package-dependent. The above ratings were determined using a Cree SMT package (with silicone encapsulation
2. Product resistance to electrostatic discharge (ESD) according to the HBM is measured by simulating ESD using a rapid avalanche
3. All products conform to the listed minimum and maximum specifications for electrical and optical characteristics when assembled
Copyright © 2011 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the
Cree logo are registered trademarks, and TR and TR3470M are trademarks of Cree, Inc.
2
Maximum Ratings at T
DC Forward Current
Peak Forward Current (1/10 duty cycle @ 1 kHz)
LED Junction Temperature
Reverse Voltage
Operating Temperature Range
Storage Temperature Range
Electrostatic Discharge Threshold (HBM)
Electrostatic Discharge Classification (MIL-STD-883E)
Typical Electrical/Optical Characteristics at T
Part Number
C450TR3547M-Sxx00
C460TR3547M-Sxx00
Mechanical Specifications
Description
P-N Junction Area (μm)
Chip Area (μm)
Chip Thickness (μm)
Au Bond Pad Diameter Anode (μm)
Au Bond Pad Thicknesses (μm)
Au Bond Pad Area Cathode (μm)
Bottom Area (μm)
Bottom Contact Metal (μm)
Bottom Contact Metal Thickness (μm)
and intrinsic AuSn metal die attach) for characterization. Ratings for other packages may differ. Junction temperature should be
characterized in a specific package to determine limitations. Assembly processing temperature must not exceed 325°C (< 5
seconds).
energy test (RAET). The RAET procedures are designed to approximate the maximum ESD ratings shown.
and operated at 50 mA within the maximum ratings shown above. Efficiency decreases at higher currents. Typical values given
are within the range of average values expected by manufacturer in large quantities and are provided for information only. All
measurements were made using lamps in T-1 3/4 packages (with Hysol OS4000 epoxy encapsulant and intrinsic AuSn metal die
attach). Optical characteristics measured in an integrating sphere using Illuminance E.
CPR3FL Rev. -
A
= 25°C
Notes 1&3
Min.
Note 2
2.8
2.8
Forward Voltage (V
A
= 25°C, If = 50 mA
Typ.
Note 2
3.2
3.2
f
, V)
Max.
3.5
3.5
Note 3
Reverse Current
[I(Vr=5V), μA]
Max.
2
2
Dimension
310 x 430
350 x 470
200 x 320
160 x 280
98 x 98
155
1.0
3.0
90
CxxxTR3547M-Sxx00
CxxxTR3547M-Sxx00
-40°C to +100°C
-40°C to +100°C
Full Width Half Max
150 mA
200 mA
1000 V
Class 2
150°C
5 V
(λ
USA Tel: +1.919.313.5300
D
Typ.
, nm)
20
21
Tolerance
Durham, NC 27703
-5, +15
-5, +15
4600 Silicon Drive
±0.5
±1.0
±35
±35
±15
±35
±25
www.cree.com
Cree, Inc.