ltc1730es8-4.2-trpbf Linear Technology Corporation, ltc1730es8-4.2-trpbf Datasheet - Page 10
![no-image](/images/manufacturer_photos/0/3/389/linear_technology_corporation_sml.jpg)
ltc1730es8-4.2-trpbf
Manufacturer Part Number
ltc1730es8-4.2-trpbf
Description
Lithium-ion Battery Pulse Chargers With Overcurrent Protection
Manufacturer
Linear Technology Corporation
Datasheet
1.LTC1730ES8-4.2-TRPBF.pdf
(12 pages)
APPLICATIO S I FOR ATIO
LTC1730-4/LTC1730-4.2
Surface mount packages rely primarily on the copper leads
(pins) to conduct the heat from the package to the sur-
rounding PC board copper which is acting as a heat sink.
The ground pin is especially important for conducting heat
as well as providing an electrical connection. Use gener-
ous amounts of copper around the ground pin and also
consider feedthrough vias (plated through holes) to back-
side or inner copper layers to maximize power dissipation.
Table 1 lists the thermal resistance for the SO-8 package.
Measured values of thermal resistance for several differ-
ent board sizes and copper areas are listed. All measure-
ments were taken in still air on 0.062" FR-4 board with one
ounce copper.
Calculating Junction Temperature
Example: Find the maximum junction temperature for a
battery voltage of 4V (V
V
maximum ambient temperature of 75 C.
The power dissipated by the IC is:
The SO-8 package for the LTC1730 features a special lead
frame with a lower thermal resistance and higher allow-
able power dissipation. The junction-to-ambient thermal
resistance of this package when soldered to a PC board is
approximately 80 C/W depending on the copper area. So
the junction temperature rise above ambient will be
approximately:
The maximum junction temperature is equal to the maxi-
mum junction temperature rise above ambient plus the
maximum ambient temperature or:
10
BAT
P = (I
(0.354W)(80 C/W) = 28.3 C
T
JMAX
= (1A • 1A • 0.35 ) + (4V • 1mA)
= 0.35 + 0.004
= 0.354W
in the fast charge mode), charge current of 1A and a
BAT
= 75 C + 28.3 C = 103.3 C
• I
BAT
• R
U
DS(ON)
CC
U
will collapse to approximately
) + (V
CC
W
• I
CC
)
U
Table 1. SO-8 Package Thermal Resistance
*Device is mounted on topside.
Output Voltage Selection (LTC1730EGN-4)
The float voltage at the BAT pin can be selected by the SEL
pin. Shorting the SEL pin to ground will set the float
voltage to 4.1V, while connecting it to V
This feature allows the charger to be used with different
types of Li-Ion cells.
ACPR Output Pin (LTC1730EGN-4)
When the input voltage is 40mV higher than the voltage at
the BAT pin, the ACPR pin is pulled low to ground to
indicate that the input supply (wall adapter) is applied.
After the input supply is removed, this pin becomes high
impedance. An internal 80ms delay prevents the LTC1730
from turning off if the voltage at the V
too close to V
FAULT Output Pin (LTC1730EGN-4)
The FAULT pin is pulled to ground when either one of the
following conditions is detected:
1. The voltage at the NTC/SHDN pin is out of the operation
2. The voltage at the BAT pin stays below 2.45V for 1/4 of
2500mm
1000mm
TOPSIDE
250mm
range. With a 10k negative temperature coefficient
thermistor placed near the battery pack, this pin indi-
cates that the temperature of the pack is either too cold
or too hot and the charger is suspended. Once the
temperature is back to the operational range, the FAULT
pin becomes high impedance and the charging re-
sumes.
the programmed charge time. If V
with 35mA of trickle charge current for 1/4 of the total
COPPER AREA
2
2
2
BACKSIDE
2500mm
2500mm
2500mm
BAT
because of the parasitic inductance.
2
2
2
BOARD AREA
2500mm
2500mm
2500mm
TOTAL
2
2
2
(JUNCTION-TO-AMBIENT)
BAT
THERMAL RESISTANCE
CC
pin rings and gets
CC
remains low even
sets it to 4.2V.
80 C/W
80 C/W
85 C/W
sn1730 1730fs