S25FL128P Meet Spansion Inc., S25FL128P Datasheet - Page 36
![no-image](/images/no-image-200.jpg)
S25FL128P
Manufacturer Part Number
S25FL128P
Description
128 Megabit Cmos 3.0 Volt Flash Memory With 104 Mhz Spi Serial Peripheral Interface Bus
Manufacturer
Meet Spansion Inc.
Datasheet
1.S25FL128P.pdf
(48 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
S25FL128P0XMFI000
Manufacturer:
SPANSION
Quantity:
20 000
Company:
Part Number:
S25FL128P0XMFI001
Manufacturer:
HARRIS
Quantity:
2 300
Part Number:
S25FL128P0XMFI001
Manufacturer:
SPANSIO
Quantity:
20 000
Company:
Part Number:
S25FL128P0XMFI003
Manufacturer:
VISHAY
Quantity:
12 559
Part Number:
S25FL128P0XMFI003
Manufacturer:
SPANSION
Quantity:
20 000
Company:
Part Number:
S25FL128P0XMFI011
Manufacturer:
SAMSUNG
Quantity:
1 576
Company:
Part Number:
S25FL128P0XNFI000
Manufacturer:
SPANSION
Quantity:
1 000
Company:
Part Number:
S25FL128P0XNFI001
Manufacturer:
SPANSION
Quantity:
300
Part Number:
S25FL128P0XNFI013
Manufacturer:
SPANSION
Quantity:
20 000
Part Number:
S25FL128PIF
Manufacturer:
SPANSION
Quantity:
20 000
11.13 Release from Deep Power Down (RES: ABh)
11.14 Release from Deep Power Down and Read Electronic Signature (RES: ABh)
36
11.14.1
Serial Mode
The device requires the Release from Deep Power Down (RES) command to exit the Deep Power Down
mode. When the device is in the Deep Power Down mode, all commands except RES are ignored.
The host system must drive CS# low and write the RES command to SI. CS# must be driven low for the entire
duration of the sequence. The command sequence is shown in
The host system must drive CS# high t
from DP mode to the standby mode after a delay of t
the device can execute any read or write command.
This command reads the old-style Electronic Signature from the SO serial output pin. See
Table 11.6
consists of the Device ID portion of the 16-bit JEDEC ID that is read by the Read Identifier (RDID) instruction.
The old style Electronic Signature is supported for backward compatibility, and should not be used for new
software designs, which should instead use the JEDEC 16-bit Electronic Signature by issuing the Read
Identifier (RDID) command.
The device is first selected by driving the CS# chip select input pin to the logic low state. The RES command
is shifted in followed by three dummy bytes onto the SI serial input pin. After the last bit of the three dummy
bytes is shifted into the device, a byte of Electronic Signature will be shifted out of the SO serial output pin.
Each bit is shifted out during the falling edge of the SCK serial clock signal. The maximum clock frequency for
the RES (ABh) command is at 104 MHz.
The Electronic Signature can be read repeatedly by applying multiples of eight clock cycles.
The RES instruction sequence is terminated by driving the CS# chip select input pin to the logic high state
anytime during data output. After issuing any Read ID commands (90h, 9Fh, ABh), driving the CS# chip
select input pin to the logic high state will automatically send the device into the standby mode. Driving the
CS# chip select input pin to the logic low state again will automatically sent the device out of the standby
mode and into the active mode.
for the command sequence and signature value. Please note that the Electronic Signature only
SO/PO[7-0]
Figure 11.19 Release from Deep Power Down (RES) Command Sequence
SCK
CS#
SI
Mode 3
Mode 0
Hi-Z
D a t a
RES(max)
S25FL128P
S h e e t
0
after the 8-bit RES command byte. The device transitions
1
Deep Power-down Mode
2
RES
( P r e l i m i n a r y )
Command
3
(see
4
Table 19.1 on page
Figure 11.19
5
6
7
and
S25FL128P_00_04 July 2, 2007
Table
42). In the standby mode,
t
RES
11.6.
Standby Mode
Figure 11.20
and