isl6261a Intersil Corporation, isl6261a Datasheet - Page 16

• Manufacturer Part Number: isl6261a
• Description: Single-phase Core Regulator For Imvp-6 Mobile Cpus
• Manufacturer: Intersil Corporation

The IMVP-6
associated with regulating the output voltage. SLEWRATE,
given in the IMVP-6
the SOFT capacitor, C
If SLEWRATE is 10mV/μs, and I
is calculated as:
Choosing 0.015μF will guarantee 10mV/μs SLEWRATE at
minimum I
up slew rate as well. One should expect the output voltage to
slew to the Boot value of 1.2V at a rate given by Equation 4:
Selecting Rbias
To properly bias the ISL6261A, a reference current needs to be
derived by connecting a 147k, 1% tolerance resistor from the
RBIAS pin to ground. This provides a very accurate 10μA
current source from which OCSET reference current is derived.
Caution should be used during layout. This resistor should
be placed in close proximity to the RBIAS pin and be
connected to good quality signal ground. Do not connect any
other components to this pin, as they will negatively impact
the performance. Capacitance on this pin may create
instabilities and should be avoided.
C
C
dV
SOFT
SOFT
dt
FIGURE 6. SIMPLIFIED VOLTAGE DROOP CIRCUIT WITH CPU-DIE VOLTAGE SENSING AND INDUCTOR DCR CURRENT SENSING
soft
=
=
=
VDIFF
C
INTERNAL TO ISL6261A
200
SLEWRATE
GV
OC
I
SOFT
ss
®
value. This choice of C
μA
specification reveals the critical timing
I
GV
=
0
(
10
.
41
015
®
mV
specification, determines the choice of
μA
SOFT
1
1
μF
μs
, through Equation 2:
=
16
)
2
=
.
8
GV
mV
20
10µA
is typically 200μA, C
nF
DROOP
SOFT
μs
controls the start-
DROOP
OCSET
VSUM
VSEN
DFB
RTN
VO
1000pF
1000pF
(EQ. 2)
(EQ. 3)
(EQ. 4)
330pF
SOFT
R ocset
ISL6261A
0~10
Start-up Operation - CLK_EN# and PGOOD
The ISL6261A provides a 3.3V logic output pin for
CLK_EN#. The system 3.3V voltage source connects to the
3V3 pin, which powers internal circuitry that is solely devoted
to the CLK_EN# function. The output is a CMOS signal with
4mA sourcing and sinking capability. CMOS logic eliminates
the need for an external pull-up resistor on this pin,
eliminating the loss on the pull-up resistor caused by
CLK_EN# being low in normal operation. This prolongs
battery run time. The 3.3V supply should be decoupled to
digital ground, not to analog ground, for noise immunity.
At start-up, CLK_EN# remains high until 13 clock cycles
after the core voltage is within 20mV of the boot voltage. The
ISL6261A triggers an internal timer for the IMVP6_PWRGD
signal (PGOOD pin). This timer allows PGOOD to go high
approximately 7ms after CLK_EN# goes low.
Static Mode of Operation - Processor Die Sensing
Remote sensing enables the ISL6261A to regulate the core
voltage at a remote sensing point, which compensates for
various resistive voltage drops in the power delivery path.
The VSEN and RTN pins of the ISL6261A are connected to
Kelvin sense leads at the die of the processor through the
processor socket. (The signal names are Vcc_sense and
Vss_sense respectively). Processor die sensing allows the
voltage regulator to tightly control the processor voltage at
the die, free of the inconsistencies and the voltage drops due
to layouts. The Kelvin sense technique provides for
extremely tight load line regulation at the processor die side.
I phase
VCC-SENSE
VSS-SENSE
R s
L
SOCKET KELVIN
TO PROCESSOR
CONECTIONS
DCR
V o
December 21, 2007
C
ESR
o
FN6354.2