isl22512 Intersil Corporation, isl22512 Datasheet
isl22512
Available stocks
Related parts for isl22512
isl22512 Summary of contents
Page 1
... Shutdown mode disconnects the top of the resistor chain and moves the wiper to the lowest position, minimizing power consumption. The three terminals accessing the resistor chain naturally configure the ISL22512 as a voltage divider. A rheostat is easily formed by floating an end terminal or connecting it to the wiper. V ...
Page 2
... SS GENERAL 2 ISL22512 ASE BRIEF DESCRIPTION 4-BIT PU UP/DOWN COUNTER PD RH 4-BIT NONVOLATILE RW MEMORY STORE AND RL CONTROL RECALL ASE CIRCUITRY ISL22512 (10 LD µTQFN) TOP VIEW ASE ONE OF THIRTY ...
Page 3
... RESISTOR MODE (Measurements between RW and RL with RH not connected, or between RW and RH with RL not connected) RINL Integral Non-Linearity (Note 15) RDNL Differential Non-Linearity (Note 14) 3 ISL22512 Thermal Information Thermal Resistance (Typical, Notes 0.3 10 Lead µTQFN . . . . . . . . . . . . . . . . . CC 8 Lead SOIC . . . . . . . . . . . . . . . . . . . . Maximum Junction Temperature (Plastic Package +150°C CC Pb-free reflow profile ...
Page 4
... Max Ri Min Ri +165°C + 17. Limits should be considered typical and are not production tested. 18. Parts are 100% tested at +25°C. Temperature limits established by characterization and are not production tested. 4 ISL22512 TEST CONDITIONS W option U option TEST CONDITIONS V = 5.5V, perform wiper move CC operation ...
Page 5
... the AC timing diagram refers to the minimum incremental change in the wiper voltage. Shutdown Mode Timing AUTOSTORE Mode Timing (HIGH) ASE (LOW) WIPER N POSITION 5 ISL22512 GAP FAST t S SLOW * 250ms ...
Page 6
... CC -0. TAP POSITION (DECIMAL FIGURE 3. DNL vs TAP POSITION IN VOLTAGE DIVIDER MODE FOR 10kΩ (W) 0.0030 V = 2.7V 0.0025 CC 0.0020 0.0015 0.0010 0.0005 0 -40 - TEMPERATURE (ºC) FIGURE 5. ZS ERROR vs TEMPERATURE 6 ISL22512 3.0 2.5 2.0 1.5 1 5.5V CC 0.05 0.00 -0.05 -0. FIGURE 4. INL vs TAP POSITION IN VOLTAGE DIVIDER -0 ...
Page 7
... FIGURE 9. END TO END R % CHANGE vs TOTAL TEMPERATURE 300 250 200 V = 2.7V CC 150 100 TAP POSITION (DECIMAL) FIGURE 11. TC FOR RHEOSTAT MODE IN ppm 7 ISL22512 (Continued) 0.5 0.3 0.1 -0.1 -0.3 -0 FIGURE 8. INL vs TAP POSITION IN RHEOSTAT MODE FOR 2. 110 FIGURE 10 ...
Page 8
... RH RL The V ramp rate specification is always in effect. CC Pin Descriptions RH and RL The RH and RL pins of the ISL22512 are equivalent to the fixed terminals of a mechanical potentiometer. The minimum voltage is V and the maximum and RL references the relative position of the terminal in relation to wiper movement direction. ...
Page 9
... Shutdown Mode The ISL22512 enters into Shutdown Mode if both PU and PD inputs are kept LOW for 2 seconds. In this mode, the resistors array is totally disconnected from its RH pin and the wiper is moved to position closest to RL pin, as shown in Figure 13. Note, that PU and PD inputs must be pulled LOW within t time window of 15ms, see “ ...
Page 10
... The lead width “B”, as measured 0.36mm (0.014 inch) or greater above the seating plane, shall not exceed a maximum value of 0.61mm (0.024 inch). 10. Controlling dimension: MILLIMETER. Converted inch dimensions are not necessarily exact. 10 ISL22512 M8.15 (JEDEC MS-012-AA ISSUE C) 8 LEAD NARROW BODY SMALL OUTLINE PLASTIC PACKAGE M B ...
Page 11
... However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 11 ISL22512 L10.2.1x1. ...