SPECIFICATIONS
Contact
Notes:
#1 This value can change due to the switching frequency, environmental conditions,
#2 The upper limit for the ambient temperature is the maximum temperature that
Remarks
* Specifications will vary with foreign standards certification ratings.
*
*
*
*
*
*
*
*
*
*
*
Arrangement
Initial contact resistance, max.
(By voltage drop 6 V DC 1 A)
Contact material
Rating
Expected
life (min.
operations)
1
2
3
4
5
6
7
8
9
10
11
RoHS Directive compatibility information
and desired reliability level, therefore it is recommended to check this with the
actual load. (AgPd contact type or SX relays are available for low level load
switching [10V DC, 10mA max. level])
can satisfy the coil temperature rise. Under the packing condition, allowable
temperature range is from –40 to +70°C
Measurement at same location as “Initial breakdown voltage” section.
Detection current: 10 mA
By resistive method; nominal voltage applied to the coil; contact carrying current: 2 A.
By resistive method; nominal voltage applied to the coil; contact carrying current: 1 A.
Nominal voltage applied to the coil, excluding contact bounce time.
Nominal voltage applied to the coil, excluding contact bounce time without diode.
Half-wave pulse of sine wave: 6 ms.; detection time: 10 µs.
Half-wave pulse of sine wave: 11 ms.; detection time: 10 µs.
Half-wave pulse of sine wave: 6 ms.
Detection time: 10 µs.
Refer to 6. Conditions for operation, transport and storage mentioned in
AMBIENT ENVIRONMENT.
.591
15
http://www.nais-e.com/
Nominal switching
capacity (resistive load)
Max. switching power
(resistive load)
Max. switching voltage
Max. switching current
Min. switching capacity
(Reference value)
Nominal
operating
power
Mechanical (at 180 cpm)
Electrical (at 20 cpm)
.291
7.4
.323
8.2
Single side
stable
1 coil
latching
.591
15
#1
mm
–40° to
Standard (B.B.M)
All Rights Reserved © COPYRIGHT Matsushita Electric Works, Ltd.
Standard contact: Ag+Au clad, AgPd
10
(1.5 to 12 V DC)
(1.5 to 12 V DC)
5 ×10
.291
7.4
contact (low level load): AgPd+Au
clad (stationary), AgPd (movable)
DC resistive)
2 A 30 V DC
5
(24 V DC)
(24 V DC)
220 V DC
resistive),
2 Form C
(2 A 30 V DC
inch
.333
200 mW
230 mW
150 mW
170 mW
8.4
60 W
5
type
2 A
10
+158°F.
(1 A 30 V
8
10 µA 10 mV DC
supplementary insulation class
FEATURES
• Approved to the supplementary
insulation class in the EN standards
(EN41003).
The insulation distance between the
contact and coil meet the supplementary
insulation class of the EN41003
standards as required for equipment
connected to the telephone lines in
Europe.
Satisfies the following conditions:
• Clearances: 2.0 mm
• Creepage distance: 2.5 mm
more
HIGH INSULATION RELAYS
100 mΩ
of EN Standards (EN41003))
10
(1.5 to 12 V DC)
1 A 30 V DC
5
M.B.B.type
110 V DC
(24 V DC)
2 Form D
(1 A 30 V DC
resistive)
250 mW
270 mW
(Conforming to the
30 W
1 A
10
—
7
.079 inch
Characteristics
*
Initial insulation resistance*
Initial
break-
down
voltage*
Initial
surge
voltage
Temperature rise (at 20°C)
Operate time [Set time]*
(at 20°C)
Release time [Reset time]*
(at 20°C)
M.B.B. time*
Shock
resistance
Vibration
resistance
Conditions for
operation, transport
and storage*
(Not freezing and
condensing at low
temperature)
Unit weight
12
M.B.B. time:
.098 inch
2
or more
12
Between open
contacts
Between contact
and coil
Between contact
sets
Between contacts,
10 ×160 µs
Between contact
and coil, 2×10 µs
11
Functional
Destructive*
Functional*
Destructive
or
Ambient
temp.
Humidity
5
×
Measuring
condition
6
1
#2
• 2,000 V breakdown voltage between
contact and coil.
• Outstanding surge resistance.
Surge withstand between open contacts:
1,500 V 10×160 µsec. (FCC part 68)
Surge withstand between contact and
coil: 2,500 V 2×10 µsec. (Telcordia)
• High contact capacity: 2 A 30 V DC
(Standard type)
• M.B.B. type available
• The use of gold-clad twin crossbar
contacts ensures high contact
reliability.
10
TX-D RELAYS
9
Min. 750 m/s
Standard (B.B.M) type
1,000 Vrms for 1 min.
10 to 55 Hz at double amplitude of 3.3 mm
10 to 55 Hz at double amplitude of 5 mm
[FCC Part 68]
Max. 50°C*
–40°C to +85°C
1,500 V
Min. 1,000 MΩ (at 500 V DC)
—
Min. 1,000 m/s
Max. 4 ms [Max. 4 ms]
Max. 4 ms [Max. 4 ms]
2,000 Vrms for 1 min.
1,000 Vrms for 1 min.
2
Approx. 2 g
2,500 V [Telcordia]
{75 G}*
5 V DC
3
5 to 85%R.H.
500 Ω
Min. 10 µs
7
–40°F to +185°F
Min. 500 m/s
.071 oz.
500 Vrms for 1 min.
2
{100 G}
Max. 50°C*
M.B.B.type
Min. 10 µs
–
TX-D
2
{50 G}*
4
TESTING
8