25AA256 Microchip Technology, 25AA256 Datasheet - Page 6
![no-image](/images/manufacturer_photos/0/4/439/microchip_technology_sml.jpg)
25AA256
Manufacturer Part Number
25AA256
Description
256K SPI Bus Serial EEPROM
Manufacturer
Microchip Technology
Datasheet
1.25AA256.pdf
(26 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
25AA256-E/P
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
Part Number:
25AA256-E/SN
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
Part Number:
25AA256-E/ST
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
Company:
Part Number:
25AA256-I/MF
Manufacturer:
MICROCHIP
Quantity:
12 000
Company:
Part Number:
25AA256-I/P
Manufacturer:
MICROCHIP
Quantity:
3 600
Company:
Part Number:
25AA256-I/P
Manufacturer:
MICROCHIP
Quantity:
3 600
Company:
Part Number:
25AA256-I/P
Manufacturer:
MICROCHIP
Quantity:
12 000
Company:
Part Number:
25AA256-I/P
Manufacturer:
MICROCHIP
Quantity:
3 600
Part Number:
25AA256-I/P
Manufacturer:
MICROCHI
Quantity:
20 000
Part Number:
25AA256-I/SM
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
www.DataSheet4U.com
25AA256/25LC256
2.0
2.1
The 25XX256 is a 32,768-byte Serial EEPROM
designed to interface directly with the Serial Peripheral
Interface (SPI) port of many of today’s popular
microcontroller families, including Microchip’s PIC
microcontrollers. It may also interface with microcon-
trollers that do not have a built-in SPI port by using
discrete I/O lines programmed properly in firmware to
match the SPI protocol.
The 25XX256 contains an 8-bit instruction register. The
device is accessed via the SI pin, with data being
clocked in on the rising edge of SCK. The CS pin must
be low and the HOLD pin must be high for the entire
operation.
Table 2-1 contains a list of the possible instruction
bytes and format for device operation. All instructions,
addresses, and data are transferred MSB first, LSB
last.
Data (SI) is sampled on the first rising edge of SCK
after CS goes low. If the clock line is shared with other
peripheral devices on the SPI bus, the user can assert
the HOLD input and place the 25XX256 in ‘HOLD’
mode. After releasing the HOLD pin, operation will
resume from the point when the HOLD was asserted.
2.2
The device is selected by pulling CS low. The 8-bit
READ instruction is transmitted to the 25XX256
followed by the 16-bit address, with the first MSB of the
address being a “don’t care” bit. After the correct READ
instruction and address are sent, the data stored in the
memory at the selected address is shifted out on the
SO pin. The data stored in the memory at the next
address can be read sequentially by continuing to
provide clock pulses. The internal Address Pointer is
automatically incremented to the next higher address
after each byte of data is shifted out. When the highest
address is reached (7FFFh), the address counter rolls
over to address 0000h allowing the read cycle to be
continued indefinitely. The read operation is terminated
by raising the CS pin (Figure 2-1).
DS21822F-page 6
FUNCTIONAL DESCRIPTION
Principles of Operation
Read Sequence
®
2.3
Prior to any attempt to write data to the 25XX256, the
write enable latch must be set by issuing the WREN
instruction (Figure 2-4). This is done by setting CS low
and then clocking out the proper instruction into the
25XX256. After all eight bits of the instruction are
transmitted, the CS must be brought high to set the
write enable latch. If the write operation is initiated
immediately after the WREN instruction without CS
being brought high, the data will not be written to the
array because the write enable latch will not have been
properly set.
Once the write enable latch is set, the user may
proceed by setting the CS low, issuing a WRITE
instruction, followed by the 16-bit address, with the first
MSB of the address being a “don’t care” bit, and then
the data to be written. Up to 64 bytes of data can be
sent to the device before a write cycle is necessary.
The only restriction is that all of the bytes must reside
in the same page.
For the data to be actually written to the array, the CS
must be brought high after the Least Significant bit (D0)
of the n
brought high at any other time, the write operation will
not be completed. Refer to Figure 2-2 and Figure 2-3
for more detailed illustrations on the byte write
sequence and the page write sequence, respectively.
While the write is in progress, the STATUS register may
be read to check the status of the WPEN, WIP, WEL,
BP1 and BP0 bits (Figure 2-6). A read attempt of a
memory array location will not be possible during a
write cycle. When the write cycle is completed, the
write enable latch is reset.
Note:
th
Write Sequence
data byte has been clocked in. If CS is
Page write operations are limited to writing
bytes within a single physical page,
regardless of the number of bytes
actually being written. Physical page
boundaries start at addresses that are
integer multiples of the page buffer size (or
‘page size’) and, end at addresses that are
integer multiples of page size – 1. If a
Page Write command attempts to write
across a physical page boundary, the
result is that the data wraps around to the
beginning of the current page (overwriting
data previously stored there), instead of
being written to the next page as might be
expected. It is therefore necessary for the
application software to prevent page write
operations that would attempt to cross a
page boundary.
© 2007 Microchip Technology Inc.