LTC3458L Linear Technology, LTC3458L Datasheet - Page 11

• Manufacturer Part Number: LTC3458L
• Description: 1.7A/ 1.5MHz Synchronous Step-Up DC/DC Converter with Output Disconnect
• Manufacturer: Linear Technology

APPLICATIO S I FOR ATIO
COMPONENT SELECTION
Inductor Selection
The high frequency operation of the LTC3458L allows for
the use of small surface mount inductors. Since the
internal slope compensation circuit relies on the inductor’s
current slope and frequency, Table 1 should be used to
select an inductor value for a given frequency of operation
(± 25%). The recommended value will yield optimal tran-
sient performance while maintaining stable operation.
Inductor values larger than listed in Table 1 are permis-
sible to reduce the current ripple.
Table 1. Recommended Inductor Values
For high efficiency, choose an inductor with high fre-
quency core material, such as ferrite, to reduce core
losses. The inductor should have low ESR (equivalent
series resistance) to reduce the I
able to handle the peak inductor current without saturat-
ing. Molded chokes or chip inductors usually do not have
enough core to support peak inductor currents in the
1A to 3A region. To minimize radiated noise, use a
toroidal or shielded inductor. (Note that the inductance of
shielded types will drop more as current increases, and
will saturate more easily). See Table 2 for a list of inductor
manufacturers.
Table 2. Inductor Vendor Information
Supplier
Coilcraft
TDK
Murata
Sumida
COEV
Toko
Wurth
..
Japan: 81-3-3607-5111
Frequency
Phone
1.25MHz
USA: [phone]
USA: [phone]
1.5MHz
750kHz
500kHz
1MHz
[phone]
[phone]
[phone]
[phone]
[phone]
[phone]
U
U
Website
www.coilcraft.com
www.component.tdk.com
www.murata.com
www.japanlink.com/sumida
www.coev.net
www.tokoam.com
www.we-online.com
2
R losses, and must be
W
Inductor Value(µH)
3.3 to 4.7
4.7 to 6.8
6.8 to 10
10 to 15
15 to 22
U
Some example inductor part types are:
Output Capacitor Selection
The output voltage ripple has three components to it. The
bulk value of the capacitor is set to reduce the ripple due
to charge into the capacitor each cycle. The max ripple due
to charge is given by:
where I
frequency.
The ESR (equivalent series resistance) is usually the most
dominant factor for ripple in most power converters. The
ripple due to capacitor ESR is given by:
where C
The ESL (equivalent series inductance) is also an impor-
tant factor for high frequency converters. Using small,
surface mount ceramic capacitors, placed as close as
possible to the V
Low ESR/ESL capacitors should be used to minimize
output voltage ripple. For surface mount applications, AVX
TPS Series tantalum capacitors, Sanyo POSCAP, or Taiyo
Yuden X5R type ceramic capacitors are recommended.
For through-hole applications, Sanyo OS-CON capacitors
offer low ESR in a small package size.
In all applications, a minimum of 4.7µF (generally 22µF is
recommended), low ESR ceramic capacitor should be
placed as close to the V
to a local ground plane.
Coilcraft: MSS7341 and MSS5131 Series
TDK: RLF5018T and SLF7045 Series
Murata: LQH4C and LQN6C Series
Sumida: CDRH4D28 and CDRH6D28 Series
COEV: DQ7545 Series
TOKO: D62CB and D63LCB Series
WURTH: WE-PD2 Series
V
V
RCESR
RBULK
..
P
ESR
= peak inductor current and f = switching
= I
=
= Capacitor Series Resistance.
P
C
• C
OUT
OUT
I
ESR
P
•
•
V
pins, will minimize ESL.
V
OUT
IN
OUT
•
pin as possible, and grounded
f
www.DataSheet4U.com
LTC3458L
11
3458lf