LTC2635 Linear Technology, LTC2635 Datasheet - Page 21
![no-image](/images/manufacturer_photos/0/3/388/linear_technology_sml.jpg)
LTC2635
Manufacturer Part Number
LTC2635
Description
Quad 10-Bit I2C VOUT DACs
Manufacturer
Linear Technology
Datasheet
1.LTC2635.pdf
(32 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LTC2635CMSE-HMI10
Manufacturer:
LT
Quantity:
10 000
Part Number:
LTC2635CMSE-HMI10#PBF
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Company:
Part Number:
LTC2635CMSE-HMI12
Manufacturer:
LT
Quantity:
10 000
Part Number:
LTC2635CMSE-HMI12#PB
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Company:
Part Number:
LTC2635CMSE-HMI12#PBF
Manufacturer:
Linear Technology
Quantity:
135
Part Number:
LTC2635CMSE-HMI12#PBF
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Company:
Part Number:
LTC2635CMSE-HMI8
Manufacturer:
LT
Quantity:
10 000
Company:
Part Number:
LTC2635CMSE-HZ10
Manufacturer:
LT
Quantity:
10 000
Part Number:
LTC2635CMSE-HZ12#PBF
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Part Number:
LTC2635CMSE-HZ8#PBF
Manufacturer:
LINEAR/凌特
Quantity:
20 000
www.DataSheet4U.com
The LTC2635 is a family of quad voltage output DACs in
16-pin QFN and 10-lead MSOP packages. Each DAC can
operate rail-to-rail using an external reference, or with its
full-scale voltage set by an integrated reference. Eighteen
combinations of accuracy (12-, 10-, and 8-bit), power-on
reset value (zero-scale, mid-scale in internal reference
mode, or mid-scale in external reference mode), DAC
power-down output load (high impedance or 200kΩ),
and full-scale voltage (2.5V or 4.096V) are available. The
LTC2635 is controlled using a 2-wire I
Power-On Reset
The LTC2635-HZ/-LZ clear the output to zero-scale when
power is fi rst applied, making system initialization con-
sistent and repeatable.
For some applications, downstream circuits are active
during DAC power-up, and may be sensitive to nonzero
outputs from the DAC during this time. The LTC2635
contains circuitry to reduce the power-on glitch: the
analog output typically rises less than 5mV above zero-
scale during power on. In general, the glitch amplitude
decreases as the power supply ramp time is increased.
See “Power-On Reset Glitch” in the Typical Performance
Characteristics section.
The LTC2635-HMI/-LMI/-LMX provide an alternative
reset, setting the output to mid-scale when power is fi rst
applied. The LTC2635-LMI and LTC2635-HMI power
up in internal reference mode, with the output set to a
mid-scale voltage of 1.25V and 2.048V, respectively. The
LTC2635-LMX power-up in external reference mode, with
the output set to mid-scale of the external reference. The
LTC2635-LMO powers up in in-ternal reference mode with
all the DAC channels placed in the high-impedance state
(powered-down). Input and DAC registers are set to the
mid-scale code, and only the internal reference is powered
up, causing supply current to be typically 100μA upon
power up. Default reference mode selection is described
in the Reference Modes section.
Power Supply Sequencing
The voltage at REF (Pin 10 – QFN, Pin 7 – MSOP) must
be kept within the range –0.3V ≤ V
Absolute Maximum Ratings). Particular care should be
OPERATION
REF
2
≤ V
C interface.
CC
+ 0.3V (see
taken to observe these limits during power supply turn-
on and turn-off sequences, when the voltage at V
transition.
Transfer Function
The digital-to-analog transfer function is
where k is the decimal equivalent of the binary DAC input
code, N is the resolution, and V
LMI/-LMX/-LMO/-LZ) or 4.096V (LTC2635-HMI/-HZ) when
in Internal Reference mode, and the voltage at REF when
in External Reference mode.
I
The LTC2635 communicates with a host using the stan-
dard 2-wire I
1 and 2) show the timing relationship of the signals on
the bus. The two bus lines, SDA and SCL, must be high
when the bus is not in use. External pull-up resistors or
current sources are required on these lines. The value of
these pull-up resistors is dependent on the power supply
and can be obtained from the I
bus operating in the fast mode, an active pull-up will be
necessary if the bus capacitance is greater than 200pF.
The LTC2635 is a receive-only (slave) device. The master
can write to the LTC2635. The LTC2635 will not acknowl-
edge (NAK) a read request from the master.
START (S) and STOP (P) Conditions
When the bus is not in use, both SCL and SDA must be
high. A bus master signals the beginning of a communica-
tion to a slave device by transmitting a START condition.
A START condition is generated by transitioning SDA from
high to low while SCL is high.
When the master has fi nished communicating with the
slave, it issues a STOP condition. A STOP condition is
generated by transitioning SDA from low to high while
SCL is high. The bus is then free for communication with
another I
2
C Serial Interface
V
OUT(IDEAL)
2
C device.
2
C interface. The timing diagrams (Figures
=
2
k
N
(
V
REF
– V
2
REF
C specifi cations. For an I
REFLO
is either 2.5V (LTC2635-
)
+ V
LTC2635
REFLO
21
CC
is in
2635f
2
C