LT1912 Linear Technology Corporation, LT1912 Datasheet - Page 11

• Manufacturer Part Number: LT1912
• Description: Step-Down Switching Regulator
• Manufacturer: Linear Technology Corporation

www.DataSheet4U.com
www.DataSheet4U.com
APPLICATIONS INFORMATION
with a lower DCR resulting in higher effi ciency. There are
several graphs in the Typical Performance Characteristics
section of this data sheet that show the maximum load
current as a function of input voltage and inductor value
for several popular output voltages. Low inductance may
result in discontinuous mode operation, which is okay
but further reduces maximum load current. For details of
maximum output current and discontinuous mode opera-
tion, see Linear Technology Application Note 44. Finally,
for duty cycles greater than 50% (V
is a minimum inductance required to avoid subharmonic
oscillations. See AN19.
Input Capacitor
Bypass the input of the LT1912 circuit with a ceramic capaci-
tor of X7R or X5R type. Y5V types have poor performance
over temperature and applied voltage, and should not be
used. A 4.7μF to 10μF ceramic capacitor is adequate to
bypass the LT1912 and will easily handle the ripple current.
Note that larger input capacitance is required when a lower
switching frequency is used. If the input power source has
high impedance, or there is signifi cant inductance due to
long wires or cables, additional bulk capacitance may be
necessary. This can be provided with a lower performance
electrolytic capacitor.
Step-down regulators draw current from the input sup-
ply in pulses with very fast rise and fall times. The input
capacitor is required to reduce the resulting voltage
ripple at the LT1912 and to force this very high frequency
switching current into a tight local loop, minimizing EMI.
A 4.7μF capacitor is capable of this task, but only if it is
placed close to the LT1912 and the catch diode (see the
PCB Layout section). A second precaution regarding the
ceramic input capacitor concerns the maximum input
voltage rating of the LT1912. A ceramic input capacitor
combined with trace or cable inductance forms a high
quality (under damped) tank circuit. If the LT1912 circuit
is plugged into a live supply, the input voltage can ring to
twice its nominal value, possibly exceeding the LT1912’s
voltage rating. This situation is easily avoided (see the Hot
Plugging Safely section).
OUT
/V
IN
> 0.5), there
Output Capacitor and Output Ripple
The output capacitor has two essential functions. Along
with the inductor, it fi lters the square wave generated by the
LT1912 to produce the DC output. In this role it determines
the output ripple, and low impedance at the switching
frequency is important. The second function is to store
energy in order to satisfy transient loads and stabilize the
LT1912’s control loop. Ceramic capacitors have very low
equivalent series resistance (ESR) and provide the best
ripple performance. A good starting value is:
where f
output capacitance in μF . Use X5R or X7R types. This
choice will provide low output ripple and good transient
response. Transient performance can be improved with a
higher value capacitor if the compensation network is also
adjusted to maintain the loop bandwidth. A lower value
of output capacitor can be used to save space and cost
but transient performance will suffer. See the Frequency
Compensation section to choose an appropriate compen-
sation network.
When choosing a capacitor, look carefully through the
data sheet to fi nd out what the actual capacitance is under
operating conditions (applied voltage and temperature).
A physically larger capacitor, or one with a higher voltage
rating, may be required. High performance tantalum or
electrolytic capacitors can be used for the output capacitor.
Low ESR is important, so choose one that is intended for
use in switching regulators. The ESR should be specifi ed
by the supplier, and should be 0.05Ω or less. Such a
capacitor will be larger than a ceramic capacitor and will
have a larger capacitance, because the capacitor must be
large to achieve low ESR. Table 2 lists several capacitor
vendors.
C
OUT
SW
=
V
is in MHz, and C
OUT
100
f
SW
OUT
is the recommended
LT1912
11
1912f