AD9040A Analog Devices, Inc., AD9040A Datasheet - Page 5

no-image

AD9040A

Manufacturer Part Number
AD9040A
Description
10-bit 40 Msps A/d Converter
Manufacturer
Analog Devices, Inc.
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
AD9040AJN
Manufacturer:
AD
Quantity:
5 510
Part Number:
AD9040AJN
Manufacturer:
NS
Quantity:
120
Part Number:
AD9040AJN
Manufacturer:
ADI
Quantity:
129
Part Number:
AD9040AJN
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Company:
Part Number:
AD9040AJN
Quantity:
250
Part Number:
AD9040AJR
Quantity:
5 510
Part Number:
AD9040AJR
Manufacturer:
AD
Quantity:
283
Part Number:
AD9040AJR
Manufacturer:
ADI
Quantity:
218
Part Number:
AD9040AJR
Manufacturer:
AD
Quantity:
1 000
Part Number:
AD9040AJR
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Part Number:
AD9040AJRZ
Manufacturer:
ADI/亚德诺
Quantity:
20 000
REV. B
DEFINITIONS OF SPECIFICATIONS
Analog Bandwidth
The analog input frequency at which the spectral power of the
fundamental frequency (as determined by FFT analysis) is
reduced by 3 dB.
Aperture Delay
The delay between the rising edge of the ENCODE command
and the instant at which the analog input is sampled.
Aperture Uncertainty (Jitter)
The sample-to-sample variation in aperture delay.
Differential Gain
The percentage of amplitude change of a small high frequency
sine wave (3.58 MHz) superimposed on a low frequency signal
(15.734 kHz).
Differential Nonlinearity
The deviation of any code from an ideal 1 LSB step.
Differential Phase
The phase change of a small high frequency sine wave (3.58 MHz)
superimposed on a low frequency signal (15.734 kHz).
Harmonic Distortion
The rms value of the fundamental divided by the rms value of
the harmonic.
Integral Nonlinearity
The deviation of the transfer function from a reference line
measured in fractions of 1 LSB using a “best straight line” de-
termined by a least square curve fit.
Minimum Conversion Rate
The encode rate at which the SNR of the lowest analog signal
frequency tested drops by no more than 3 dB below the guaran-
teed limit.
A
IN
1mA
1k
ANALOG INPUT
V
V
2k
CC
SS
1k
1mA
V
REF
REFERENCE CIRCUIT
1k
GND
V
CC
Figure 2. Equivalent Circuits
6.8k
1k
V
SS
–5–
BP
R
2.5k
L
REF
Maximum Conversion Rate
The encode rate at which parametric testing is performed.
Output Propagation Delay
The delay between the 50% point of the falling edge of the
ENCODE command and the 1 V/4 V points of output data.
Overvoltage Recovery Time
The amount of time required for the converter to recover to
10-bit accuracy after an analog input signal 150% of full scale is
reduced to the full-scale range of the converter.
Power Supply Rejection Ratio (PSRR)
The ratio of a change in input offset voltage to a change in
power supply voltage.
Signal-to-Noise Ratio (SNR)
The ratio of the rms signal amplitude to the rms value of
“noise,” which is defined as the sum of all other spectral com-
ponents, including harmonics but excluding dc, with an analog
input signal 1 dB below full scale.
Signal-to-Noise Ratio (Without Harmonics)
The ratio of the rms signal amplitude to the rms value of
“noise,” which is defined as the sum of all other spectral com-
ponents, excluding the first eight harmonics and dc, with an
analog input signal 1 dB below full scale.
Transient Response
The time required for the converter to achieve 10-bit accuracy
when a step function is applied to the analog input.
Two-Tone Intermodulation Distortion (IMD) Rejection
The ratio of the power of either of two input signals to the
power of the strongest third-order IMD signal.
BANDGAP OUTPUT
GND
V
CC
R
L
V
OUT
CMOS OUTPUT
GND
V
AD9040A
CC
D0-9

Related parts for AD9040A