AD9517-1 Analog Devices, Inc., AD9517-1 Datasheet - Page 27
AD9517-1
Manufacturer Part Number
AD9517-1
Description
12-output Clock Generator With Integrated 2.5 Ghz Vco
Manufacturer
Analog Devices, Inc.
Datasheet
1.AD9517-1.pdf
(80 pages)
- Current page: 27 of 80
- Download datasheet (2Mb)
THEORY OF OPERATION
OPERATIONAL CONFIGURATIONS
The AD9517 can be configured in several ways. These
configurations must be set up by loading the control registers
(see Table 51 and Table 52 through Table 61). Each section
or function must be individually programmed by setting the
appropriate bits in the corresponding control register or registers.
High Frequency Clock Distribution—CLK or External
VCO >1600 MHz
The AD9517 power-up default configuration has the PLL
powered off and the routing of the input set so that the
CLK/ CLK input is connected to the distribution section
through the VCO divider (divide-by-2/divide-by-3/divide-by-4/
divide-by-5/divide-by-6). This is a distribution only mode that
allows for an external input up to 2400 MHz (see Table 3). The
maximum frequency that can be applied to the channel dividers
is 1600 MHz; therefore, higher input frequencies must be
divided down before reaching the channel dividers. This input
routing can also be used for lower input frequencies, but the
minimum divide is 2 before the channel dividers.
When the PLL is enabled, this routing also allows the use of the
PLL with an external VCO or VCXO with a frequency less than
2400 MHz. In this configuration, the internal VCO is not used,
and is powered off. The external VCO/VCXO feeds directly into
the prescaler.
The register settings shown in Table 21 are the default values of
these registers at power-up or after a reset operation. If the
contents of the registers are altered by prior programming after
power-up or reset, these registers may also be set intentionally
to these values.
Rev. 0 | Page 27 of 80
Table 21. Default Settings of Some PLL Registers
Register
0x10<1:0> = 01b
0x1E0<2:0> = 010b
0x1E1<0> = 0b
0x1E1<1> = 0b
When using the internal PLL with an external VCO, the PLL
must be turned on.
Table 22. Settings When Using an External VCO
Register
0x10 to 0x1E
0x1E1<1> = 0b
An external VCO requires an external loop filter that must be
connected between CP and the tuning pin of the VCO. This
loop filter determines the loop bandwidth and stability of the
PLL. Make sure to select the proper PFD polarity for the VCO
being used.
Table 23. Setting the PFD Polarity
Register
0x10<7> = 0b
0x10<7> = 1b
Function
PLL normal operation (PLL on)
PLL settings. Select and enable a reference
input; set R, N (P, A, B), PFD polarity, and I
according to the intended loop configuration.
Function
PLL asynchronous power-down (PLL off )
Set VCO divider = 4
Use the VCO divider
CLK selected as the source
Function
PFD polarity positive (higher control
voltage produces higher frequency)
PFD polarity negative (higher control
voltage produces lower frequency)
AD9517-1
CP
Related parts for AD9517-1
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
12-output Clock Generator With Integrated 2.8 Ghz Vco
Manufacturer:
Analog Devices, Inc.
Datasheet:
Part Number:
Description:
12-output Clock Generator With Integrated 2.2 Ghz Vco
Manufacturer:
Analog Devices, Inc.
Datasheet:
Part Number:
Description:
12-output Clock Generator With Integrated 2.0 Ghz Vco
Manufacturer:
Analog Devices, Inc.
Datasheet:
Part Number:
Description:
12-output Clock Generator With Integrated 1.6 Ghz Vco
Manufacturer:
Analog Devices, Inc.
Datasheet:
Part Number:
Description:
Ultrasonic Bubble Air-in-line Sensors
Manufacturer:
Sensortechnics GmbH
Datasheet:
Part Number:
Description:
Analog Divider
Manufacturer:
Analog Devices, Inc.
Datasheet:
Part Number:
Description:
Analog Front End For Adsl
Manufacturer:
Analog Devices, Inc.
Datasheet:
Part Number:
Description:
Lc2mos Complete, 12-bit Analog I/o System
Manufacturer:
Analog Devices, Inc.
Datasheet:
Part Number:
Description:
Cmos 4/8 Channel Analog Multiplexers
Manufacturer:
Analog Devices, Inc.
Datasheet:
Part Number:
Description:
Low Cost, Low Power Cmos General Purpose Analog Front End
Manufacturer:
Analog Devices, Inc.
Datasheet:
Part Number:
Description:
2.5 V To 5.0 V Micropower, Precision Series Mode Voltage References
Manufacturer:
Analog Devices, Inc.
Datasheet:
Part Number:
Description:
Stereo, Single-supply 18-bit Integrated Dac
Manufacturer:
Analog Devices, Inc.
Datasheet:
Part Number:
Description:
Multichannel 24-bit, 192 Khz, Dac
Manufacturer:
Analog Devices, Inc.
Datasheet:
Part Number:
Description:
Ac?97 Soundmax Codec
Manufacturer:
Analog Devices, Inc.
Datasheet:
Part Number:
Description:
Complete Dual 18-bit 16 X Fs Audio Dac
Manufacturer:
Analog Devices, Inc.
Datasheet: