SKY73023 Skyworks Solutions, SKY73023 Datasheet - Page 3
![no-image](/images/no-image-200.jpg)
SKY73023
Manufacturer Part Number
SKY73023
Description
High Gain and Linearity Diversity Downconversion Mixer
Manufacturer
Skyworks Solutions
Datasheet
1.SKY73023.pdf
(10 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
SKY73023-31
Manufacturer:
SKYWORKS/思佳讯
Quantity:
20 000
Functional Description
The SKY73023 is a high gain diversity mixer, optimized for base
station receiver applications. The device consists of two diversity
channels (A and B), each consisting of a low loss RF balun, high
linearity passive mixer, and a low noise IF amplifier.
Two LO amplifiers (independent of channels A and B) are also
included that allow the SKY73023 to connect directly to the output
of a Voltage Controlled Oscillator (VCO). This eliminates the extra
gain stages needed by most discrete passive mixers. A Single
Pole, Double Throw (SPDT) switch has been included to select
between two different LO inputs for frequency hopping
applications (i.e., GSM).
RF Baluns and Passive Mixer
The RF baluns provide a single ended input, which can easily be
matched to 50 Ω using a simple external matching circuit. The RF
baluns offer very low loss, and excellent amplitude and phase
balance.
The high linearity SKY73023 is a passive, double balanced mixer
that provides a very low conversion loss and an excellent 3
Order Input Intercept Point (IIP3).
Addtionally, the balanced nature of the mixer provides for high
port-to-port isolation.
LO Buffers and SPDT LO Switch
The LO buffers allow the input power of the SKY73023 to be in
the range of ±3 dBm. The LO section is optimized for low-side LO
injection. However, each of the two LOs can be driven over a wide
frequency range with only slight degradation in performance.
Table 2. SKY73023 Absolute Maximum Ratings
Notes: Exposure to maximum rating conditions for extended periods may reduce device reliability. There is no damage to device with only one parameter set at the limit and all other
www.DataSheet4U.com
Supply voltage, +5 V (VCC1 – VCC7)
Supply current
RF input power
LO input power
Operating case temperature
Junction temperature
Storage case temperature
parameters set at or below their nominal value.
Nominal thermal resistance (junction to center ground pad) is 5.1 °C/W.
200634C • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • July 26, 2007
Parameter
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
VCC
I
P
P
T
T
T
CC
RF
LO
C
J
STG
Symbol
rd
A high isolation SPDT switch allows the SKY73023 to be used for
frequency hopping applications. This switch provides greater than
45 dB of LO1 to LO2 isolation:
For applications that do not require frequency hopping, LO_SEL is
fixed to one state and the appropriate LO input is used. An internal
pull-down resistor enables the LO2 input.
IF Amplifier
The SKY73023 includes high dynamic range IF amplifiers that
follow the passive mixers in the signal path. The outputs require a
supply voltage connection using inductive chokes. These choke
inductors should be high-Q and have the ability to handle 200 mA
or greater.
A simple matching network allows the output ports to be matched
to a balanced 200 Ω impedance. The IF amplifiers are optimized
for IF frequencies between 40 and 300 MHz. The IF amplifiers can
be operated outside of this range, but with a slight degradation in
performance.
Electrical and Mechanical Specifications
The absolute maximum ratings of the SKY73023 are provided in
Table 2 and the recommended operating conditions in Table 3.
Electrical characteristics for the SKY73023 are provided in
Table 4.
Minimum
PRELIMINARY DATA SHEET • SKY73023 DOWNCONVERSION MIXER
–40
–40
4.5
LO_SEL Input
High
Low
Maximum
+125
440
+85
150
5.5
20
6
LO1 (pin 19) enabled
LO2 (pin 27) enabled
LO Path Selected
Units
dBm
dBm
mA
°C
°C
°C
V
3