CLAA154WB05AN CHUNGHWA PICTURE TUBES, CLAA154WB05AN Datasheet - Page 22
![no-image](/images/no-image-200.jpg)
CLAA154WB05AN
Manufacturer Part Number
CLAA154WB05AN
Description
Display Module
Manufacturer
CHUNGHWA PICTURE TUBES
Datasheet
1.CLAA154WB05AN.pdf
(23 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
CLAA154WB05AN
Manufacturer:
CPT
Quantity:
1 000
Company:
Part Number:
CLAA154WB05AN
Manufacturer:
CPT
Quantity:
1 000
www.DataSheet.co.kr
CPT
11. HANDLING PRECAUTIONS FOR TFT-LCD MODULE
Please pay attention to the followings in handling- TFT-LCD products;
11.1 ASSEMBLY PRECAUTION
11.2 OPERATING PRECAUTIONS
11.3 PRECAUTIONS WITH ELECTROSTATICS
CPT Confidential
(1) Please use the mounting hole on the module side in installing and do not beading or wrenching
(2) Please design display housing in accordance with the following guidelines.
(3) Please do not push or scratch LCD panel surface with any-thing hard. And do not soil LCD panel surface
(4) Please do not press any parts on the rear side such as source TCP, gate TCP, control circuit board and
(5) Please wipe out LCD panel surface with absorbent cotton or soft clothe in case of it being soiled.
(6) Please wipe out drops of adhesives like saliva and water on LCD panel surface immediately. They might
(7) Please do not take a LCD module to pieces and reconstruct it. Resolving and reconstructing modules may
(8) Please do not touch metal frames with bare hands and soiled gloves. A color change of the metal frames
(9) Please pay attention to handling lead wire of backlight so that it is not tugged in connecting with inverter.
(1) Please be sure to turn off the power supply before connecting and disconnecting signal input cable.
(2) Please do not change variable resistance settings in LCD module. They are adjusted to the most suitable
(3) Please consider that LCD backlight takes longer time to become stable of radiation characteristics in low
(4) A condensation might happen on the surface and inside of LCD module in case of sudden change of
(5) Please pay attention to displaying the same pattern for very long time. Image might stick on LCD. If then,
(6) Please obey the same caution descriptions as ones that need to pay attention to ordinary electronic parts.
(1) This LCD module use CMOS-IC on circuit board and TFT-LCD panel, and so it is easy to be affected by
(2) Please remove protection film very slowly on the surface of LCD module to prevent from electrostatics
LCD in assembling. And please do not drop, bend or twist LCD module in handling.
by touching with bare hands. (Polarizer film, surface of LCD panel is easy to be flawed.)
FPCs during handling LCD module. If pressing rear part is unavoidable, handle the LCD module with
care not to damage them.
damage to cause panel surface variation and color change.
cause them not to work well.
can happen during a long preservation of soiled LCD modules.
value. If they are changed, it might happen LCD does not satisfy the characteristics specification.
temperature than in room temperature.
ambient temperature.
time going on can make LCD work well.
electrostatics. Please be careful with electrostatics by the way of your body connecting to the ground
and so on.
occurrence.
Keep sufficient clearance between LCD module back surface and housing when the LCD module is
When some parts, such as, FPC cable and ferrite plate, are installed underneath the LCD module, still
Design the inverter location and connector position carefully so as not to give stress to lamp cable, or
Keep sufficient clearance between LCD module and the others parts, such as inverter and speaker so
Housing case must be destined carefully so as not to put stresses on LCD all sides and not to wrench
module. The stresses may cause non-uniformity even if there is no non-uniformity statically.
mounted. Approximately 1.0 mm of the clearance in the design is recommended taking into account
the tolerance of LCD module thickness and mounting structure height on the housing.
sufficient clearance is required, such as 0.5mm. This clearance is, especially, to be reconsidered
when the additional parts are implemented for EMI countermeasure.
not to interface the LCD module by the lamp cable.
as not to interface the LCD module. Approximately 1.0mm of the clearance in the design is
recommended.
22/ 23
CHUNGHWA PICTURES TUBES, LTD.,
CLAA154WB05A N
www.yslcd.com.tw
Datasheet pdf - http://www.DataSheet4U.net/