ADP170 Analog Devices, Inc., ADP170 Datasheet - Page 13
ADP170
Manufacturer Part Number
ADP170
Description
300 Ma, Low Quiescent Current, Cmos Linear Regulators
Manufacturer
Analog Devices, Inc.
Datasheet
1.ADP170.pdf
(20 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ADP1706ACPZ-1.1-R7
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Part Number:
ADP1706ACPZ-1.8
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Company:
Part Number:
ADP1706ARDZ-1.2
Manufacturer:
Analog Devices Inc
Quantity:
135
Part Number:
ADP1706ARDZ-1.8-R7
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Part Number:
ADP1706ARDZ-2.5
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Part Number:
ADP1706ARDZ-2.5-R7
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Company:
Part Number:
ADP1708ARDZ
Manufacturer:
Analog Devices Inc
Quantity:
1 973
Company:
Part Number:
ADP170AUJZ-1.8-R7
Manufacturer:
AD
Quantity:
6 000
In this example, the worst-case temperature coefficient
(TEMPCO) over −40°C to +85°C is assumed to be 15% for an
X5R dielectric. The tolerance of the capacitor (TOL) is assumed
to be 10%, and C
Substituting these values in Equation 1 yields
Therefore, the capacitor chosen in this example meets the
minimum capacitance requirement of the LDO over temper-
ature and tolerance at the chosen output voltage.
To guarantee the performance of the ADP170/ADP171, it is
imperative that the effects of dc bias, temperature, and toler-
ances on the behavior of the capacitors are evaluated for each
application.
UNDERVOLTAGE LOCKOUT
The ADP170/ADP171 have an internal undervoltage lockout
circuit that disables all inputs and the output when the input
voltage is less than approximately 1.2 V. This ensures that the
ADP170/ADP171 inputs and the output behave in a predictable
manner during power-up.
ENABLE FEATURE
The ADP170/ADP171 use the EN pin to enable and disable the
VOUT pin under normal operating conditions. As shown in
Figure 30, when a rising voltage on EN crosses the active
threshold, VOUT turns on. When a falling voltage on EN
crosses the inactive threshold, VOUT turns off.
As shown in Figure 30, the EN pin has hysteresis built in. This
prevents on/off oscillations that can occur due to noise on the
EN pin as it passes through the threshold points.
C
EFF
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0
= 0.94 μF × (1 − 0.15) × (1 − 0.1) = 0.719 μF
0
Figure 30. ADP170/ADP171 Typical EN Pin Operation
0.2
BIAS
is 0.94 μF at 1.8 V, as shown in Figure 29.
0.4
0.6
V
0.8
EN
1.0
1.2
1.4
1.6
Rev. 0 | Page 13 of 20
The EN pin active/inactive thresholds are derived from the VIN
voltage. Therefore, these thresholds vary with changing input
voltage. Figure 31 shows typical EN active/inactive thresholds
when the input voltage varies from 1.6 V to 3.6 V.
The ADP170/ADP171 utilize an internal soft start to limit the
inrush current when the output is enabled. The start-up time
for the 1.8 V option is approximately 120 μs from the time the
EN active threshold is crossed to when the output reaches 90%
of its final value. As shown in Figure 32, the start-up time is
dependent on the output voltage setting.
1
2
1.2
1.1
1.0
0.9
0.8
0.7
0.6
0.5
0.4
CH1
Figure 31. Typical EN Pin Thresholds vs. Input Voltage
1.00V
Figure 32. Typical Start-Up Time
CH2 1.00V
EN
EN INACTIVE
B
V
W
EN ACTIVE
IN
(V)
M20.0µs
V
T
OUT
ADP170/ADP171
79.8000µs
V
= 0.8V
OUT
V
OUT
= 3.0V
A CH1
= 1.8V
2.72V