LM111J-8-SMD National Semiconductor Corporation, LM111J-8-SMD Datasheet - Page 15

• Manufacturer Part Number: LM111J-8-SMD
• Description: Lm111qml Voltage Comparator
• Manufacturer: National Semiconductor Corporation

V
±I
I
I
±I
I
CEX
IO
CEX
IO
Symbol
Symbol
IB
IB
DC DELTA Parameters SMD 5962R0052402
The following conditions apply, unless otherwise specified. V
Delta calculations performed on QMLV devices at group B , subgroup 5.
Post Radiation Parameters SMD 5962R0052402
The following conditions apply, unless otherwise specified
R
Note 2: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is
functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics. The guaranteed
specifications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed test
conditions.
Note 3: This rating applies for ±15V supplies. The positive input voltage limits is 30 V above the negative supply. The negative input voltage limits is equal to the
negative supply voltage or 30V below the positive supply, whichever is less.
Note 4: The maximum power dissipation must be derated at elevated temperatures and is dictated by T
junction to ambient thermal resistance), and T
θ
Note 5: Human body model, 1.5 kΩ in series with 100 pF.
Note 6: Datalog reading in K=V/mV.
Note 7: Pin names based on an 8 pin package configuration. When using higher pin count packages then:
Balance / Strobe, Pin 7 is Output, and Pin 8 is V
Note 8: I
Note 9: Calculated parameter.
Note 10: Actual min. limit used is 5mA due to test setup.
Note 11: V
Note 12: Pre and post irradiation limits are identical to those listed under AC and DC electrical characteristics except as listed in the Post Radiation Limits Table.
These parts may be dose rate sensitive in a space environment and demonstrate enhanced low dose rate effect. Radiation end point limits for the noted parameters
are guaranteed only for the conditions as specified in Mil-Std-883, Method 1019, Condition A.
Note 13: Group A sample ONLY
Note 14: Pre and post irradiation limits are identical to those listed under AC and DC electrical characteristics except as listed in the Post Radiation Limits Table.
These parts may be sensitive in a high dose environment. Low dose rate testing has been performed on a wafer-by-wafer basis, per test method 1019 condition
D of MIL-STD-883, with no enhanced low dose rate sensitivity (ELDRS) effect.
Note 15: Subscript (R) indicates tests which are performed with input stage current raised by connecting BAL and BAL/STB terminals to +V
JA
or the number given in the Absolute Maximum Ratings, whichever is lower.
ST
ID
= −2mA at −55°C
is voltage difference between inputs.
Input Offset Voltage
Input Bias Current
Output Leakage Current
Raised Input Offset Current
Input Bias Current
Output Leakage Current
Parameter
Parameter
A
(ambient temperature). The maximum allowable power dissipation at any temperature is P
+
. For example:
V
+V
V
R
+V
V
R
V
+V
V
R
+V
V
R
+V
V
V
V
+V
0V, V
+V
V
I
I
I
I
I
I
O
I
I
O
S
S
S
S
= 0V, R
= 0V, V
= 0V, V
= 0V, R
= 0V, V
= 0V, V
= 0V, R
= 0V, R
CC
CC
CC
CC
CC
CC
CC
= 50Ω
= 50Ω
= 50KΩ
= 50KΩ
= 32V
= 32V
CM
= 29.5V, -V
= 2V, -V
= 29.5V, -V
= 2V, -V
= 18V, -V
= 29.5V, −V
= 18V, −V
= −14.5V, R
S
CM
CM
CM
CM
S
S
S
V
Conditions
Conditions
56
= 50Ω
= 50KΩ
= 50KΩ
= 50KΩ
is the Voltage between the Balance and Balance / Strobe pins
= -14.5V,
= +13V,
= -14.5V,
= +13V,
CC
CC
CC
CC
CC
= -28V,
= -28V,
CC
CC
CC
15
= -18V,
= ±15V, V
= −18V,
= -0.5V,
= -0.5V,
= −0.5V, V
S
= 50KΩ
CM
I
= 0
=
(Note 14)
(Note 15)
Notes
Notes
Jmax
(Note 14)
(maximum junction temperature), θ
Pin 2 & 3 are Inputs, Pin 5 is Balance, Pin 6 is
-12.5
-12.5
-12.5
−100 +100
−180
−225
−1.0
Min
-0.5
-0.5
-0.5
-5.0
Min
Max
12.5
12.5
12.5
Max
+25
0.5
0.5
0.5
5.0
0.1
0.1
Unit
Unit
mV
mV
mV
nA
nA
nA
nA
nA
nA
nA
nA
Dmax
CC
.
= (T
JA
www.national.com
(package
Jmax
groups
groups
- T
Sub-
Sub-
1
1
1
1
1
1
1
1
1
1
1
A
)/