MIC5248-1.2BM5 Micrel Semiconductor, MIC5248-1.2BM5 Datasheet
MIC5248-1.2BM5
Available stocks
Related parts for MIC5248-1.2BM5
MIC5248-1.2BM5 Summary of contents
Page 1
... Fast transient response • TTL-logic-controlled enable input Applications • Processor power-up sequencing • Laptop, notebook, and palmtop computers • PCMCIA V Ordering Information Part Number Marking Voltage MIC5248-1.2BM5 LV12 MIC5248-1.2YM5 KV12 Other voltages available. Contact Micrel for details. 47k MIC5248-x.xBM5 ...
Page 2
... Pin Number Pin Name GND OUT MIC5248 EN PG MIC5248-x.xYM5 Pin Function Supply Input Ground Enable/Shutdown (Input): CMOS compatible input. Logic high = enable; logic low = shutdown. Do not leave open. Power Good Output Regulator Output 2 Micrel GND KVxx ...
Page 3
... ................................... ....................... – +125 ......................................................235 C +125 C; unless noted. J Min Typical –3 –4 –0.3 0 4.0 0.45 100 100 = 150mA 60 OUT 160 350 1.6 0.01 0.01 150 10 89.5 0.02 0.01 1 Micrel IN IN Max Units 0.3 %/V 5 150 A 150 0 96 MIC5248 ...
Page 4
... Reference Voltage Thermal Sensor Under- voltage Lockout Overcurrent Dropout Detection Timing Diagram 96.5% V OUT Indeterminable when V low EN MIC5248 Startup/ Quickstart Shutdown Control FAULT Error Current Amplifier Amplifier ACTIVE SHUTDOWN Out of Regulation Detection Delay Min - Max 1-5ms 4 PULL UP OUT PULL DOWN ...
Page 5
... OUT -40 - 100120140 TEMPERATURE ( C) Power Good Delay vs. Input Voltage 100 A 1.9 OUT 1.8 1.7 1.6 1.5 1.4 1.3 1.2 1.1 1 2.6 3.1 3.6 4.1 4.6 5.1 5.6 6.1 INPUT VOLTAGE (V) Output Voltage vs. Input Voltage 1.195 I = 100 A OUT 1.19 1.185 1. 150mA OUT 1.175 1.17 2.6 3.1 3.6 4.1 4.6 5.1 5.6 6.1 INPUT VOLTAGE (V) Enable Voltage vs. Input Voltage 1.4 1.3 1.2 1.1 1 0.9 0.8 0 100 A OUT 0.6 2.6 3.1 3.6 4.1 4.6 5.1 5.6 6.1 INPUT VOLTAGE (V) MIC5248 ...
Page 6
... MIC5248 MIC5248 Enable Voltage vs. Temperature 1 3.3V IN 1.15 1.1 1.05 1 0.95 0.9 0.85 0.8 -40 - 100120140 TEMPERATURE ( C) Power Good Characteristic V = 12V OUT TIME (250 s/div) 6 Micrel November 2002 ...
Page 7
... D conditions that are critical to the application will give the maximum operating conditions for the regulator circuit. For example, when operating the MIC5248-1.2BM5 with a minimum footprint layout, the maximum input voltage for a set output current can be determined as follows: 125 ...
Page 8
... For a full discussion of heat sinking and thermal effects on voltage regulators, refer to the Regulator Thermals section of Micrel’s Designing with Low-Dropout Voltage Regu- lators handbook. MIC5248 Dual-Supply Operation When used in dual supply systems where the regulator load is returned to a negative supply, the output voltage must be diode clamped to ground ...
Page 9
... MIC5248 Package Information 1.90 (0.075) REF 0.95 (0.037) REF 3.02 (0.119) 2.80 (0.110) 0.50 (0.020) 0.35 (0.014) November 2002 1.75 (0.069) 3.00 (0.118) 1.50 (0.059) 2.60 (0.102) DIMENSIONS: MM (INCH) 1.30 (0.051) 0.90 (0.035 0.15 (0.006) 0.60 (0.024) 0.00 (0.000) 0.10 (0.004) SOT-23-5 (M) 9 Micrel 0.20 (0.008) 0.09 (0.004) MIC5248 ...
Page 10
... MIC5248 MIC5248 10 Micrel November 2002 ...
Page 11
... MIC5248 November 2002 11 Micrel MIC5248 ...
Page 12
... This information is believed to be accurate and reliable, however no responsibility is assumed by Micrel for its use nor for any infringement of patents or other rights of third parties resulting from its use. No license is granted by implication or otherwise under any patent or patent right of Micrel Inc. MIC5248 + 1 (408) 944-0970 http://www ...