MIC2045 Micrel Semiconductor, MIC2045 Datasheet - Page 14
![no-image](/images/manufacturer_photos/0/4/435/micrel_semiconductor_sml.jpg)
MIC2045
Manufacturer Part Number
MIC2045
Description
(MIC2044 / MIC2045) PROTECTED POWER DISTRIBUTION SWITCH
Manufacturer
Micrel Semiconductor
Datasheet
1.MIC2045.pdf
(15 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
MIC2045-1YTS
Manufacturer:
IXYS
Quantity:
2 100
Company:
Part Number:
MIC2045-2YTS
Manufacturer:
MICREL
Quantity:
230
www.DataSheet4U.com
MIC2044/2045
Power Dissipation
Power dissipation depends on several factors such as the
load, PCB layout, ambient temperature, and package type.
The following equations can be used to calculate power
dissipation and die temperature.
Calculation of power dissipation can be accomplished by the
following equation:
To relate this to junction temperature, the following equation
can be used:
where T
and R
Printed Circuit Board Hot Plug
The MIC2044/45 are ideal inrush current limiting power
switches suitable for hot plug applications. Due to the inte-
grated charge pump, the MIC2044/45 present a high imped-
ance when in the off state and the device slowly becomes a
low impedance as it turns on. This effectively isolates power
supplies from highly capacitive loads by reducing inrush
current during hot plug events. This same feature also can be
used for soft-start requirements.
PCB Layout Recommendations
The MIC2044 and MIC2045 have very low on-resistance,
typically 20m , and the switches can provide up to 6A of
continuous output current. Under heavy loads, the switched
current may cause the devices to heat up considerably. The
following list contains some useful suggestions for PCB
layout design of the MIC2044/45 in order to prevent the die
from overheating under normal operating conditions.
MIC2044/2045
P
T
(J-A)
J
D
J
= P
= R
= junction temperature, T
is the thermal resistance of the package.
D
DS(on)
R
( J-A)
m
(I
OUT
+ T
)
A
2
W
W
A
W
= ambient temperature
m
Figure 4. Lower UVLO Setting
m
W
(5)
(6)
14
1.
Micrel Semiconductor does not assume responsibility for the use of
this program tool in the event that any PCB assembled, tested,
produced, and/or manufactured becomes damaged and/or causes any
degradation of system performance or damage to any system
components in which the aforementioned PCB is included.
1. Supply additional copper area under the device
2. Provide additional pad area on the corner pins of
3. Tie the common power pins (V
4. For PCB trace width calculation, there are
to remove heat away from the IC.
See
in calculating the suggested area.
the MIC2044/45 IC for heat distribution.
13, 16 and V
manner such that the traces entering and
leaving the device have a uniform width suffi-
cient for the application’s current requirements
plus added margin (25% minimum recom-
mended).
Ex: For 4A maximum current, design traces for
5A capability.
numerous calculator programs available on the
internet and elsewhere. As a general rule of
thumb, 15-20 mils width for every 1A of current
when using 1oz. copper. However, the trace
width calculators often take into account maxi-
mum temperature increase constraints, as well
as layer arrangement, in determining the PCB
trace widths. As a reference, the following link is
suggested for trial tests in PCB trace width
calculations.
http://www.aracnet.com/cgi-usr/gpatrick/trace.pl
“Application Hint 17”
W
1
OUT
W
= pins 9, 12, 14) together in a
W
W
m
for a general guideline
IN
= pins 7, 11,
October 2003
Micrel