MTD658 MYSON TECHNOLOGY, MTD658 Datasheet - Page 10

• Manufacturer Part Number: MTD658
• Description: 8 Port 10M/100M Hub
• Manufacturer: MYSON TECHNOLOGY

REQOUT , but IACKB is asserted, means this MTD658 can get data from IDATA bus. When only one
MTD658 output REQOUT to Inter-Bus Interface, IACKB will be asserted by Inter-Bus master device, If
larger than two MTD658’ s REQOUT were asserted, Inter-Bus master will not assert IACKB , but will
assert ICOLB to inform all the connected MTD658s.
The Inter-Bus interface can also be programmed to EXT_ARB mode, using LEDDAT pin’ s jumper set-
ting. In this mode, Inter-Bus interface need an external arbitration logic to arbitrate Inter-Bus operation.
And in this mode, the stackable capability is not limitted by the MTD658’ s REQIN pins number.
3.6 10M/100M packet Switch
The MTD658 inplements a 10/100M two port switch for 10M/100M packet switching. Total 2K address
entrys are provided for packets’ SA learning and DA routing; and alsoprovide automatic aging function
( aging time = 300secs). The input packet from 10MHub ( or 100M Hub) will be stored to external
memory first, while packet is good for forward ( CRC chech ok, 64Bytes < length > 1518Bytes, and not
local packets ) , than forward this packet to 100M Hub (or 10M Hub).
3.7 Uplink Switch Port
The MTD658 can config one switch port as an uplink switch port. When UPSWEN pin is high, and
IMASTER pin is low, one of the intenal switch port is connect to 100M HUB, the other is connected to
RMII port 7. In uplink switch mode, port 7 can work in 10M/100M(from SPEED7 pin), half/full
duplex(from P7FULL pin) mode.
3.8 Memory Interface
The MTD658 use asynchronous SRAM as two port switchs’ packet buffers, total has 128K byte exter-
nal memory for packet buffering.
3.9 MII management
The MTD658 can be managed through MDC, MDIO pins. The MTD658 implements
function control and status report (see Section 4.0 on page ).
The management frame format is compliant to IEEE802.3u clause 22, and the device ID is fixed to
5’ h1f internally.
3.10 LED display
The MTD658 implements three display modes, port RX activity, 10/100M domain collision, port parti-
tion. The LED data pin LEDDAT is high actived.
One strobe pin LEDCLK(24 burst clock/per 42ms) is used to latch serial LEDDAT information, and user
can shift the latched data into byte aligned shift register to drive LEDs.
4.0 Registers
The MTD658 implements
REG
NO
0
TABLE 1. MII r egister s
Bits
5-8
0
1
2
3
4
9
CClimit100
DisPar100
DisJab100
MYSON
TECHNOLOGY
DisJab10
DisPar10
CtlReg0
Name
3
MII registers, define as following tables:
R/W
R/W
Reserved.
Set this bit will disable 10M hub core partition function.
Set this bit will disable 100M hub core partition function.
Set this bit will disable 10M hub core Jabber function.
Set this bit will disable 100M hub core Jabber function.
Reserved
Set "1" will program 100M partition cclimit to 128.
CONTROL REGISTER 0
10/17
Descriptions
MTD658 Revision 2.0 17/03/2000
MTD658
3
MII registers for
www.DataSheet4U.com
1’ b0(64)
Default
4’ b000
1’ b0
1’ b0
1’ b0
1’ b0
1’ b0