AN1984 Freescale Semiconductor / Motorola, AN1984 Datasheet
![no-image](/images/no-image-200.jpg)
AN1984
Related parts for AN1984
AN1984 Summary of contents
Page 1
... Figure 3. SSOP Axial Style Port connection. Pick up nozzles for these packages should be configured to apply vacuum only to the flat surface of a port base. An access clearance in the nozzle for a port shank is necessary to properly handle these device configurations. See AN1984 Rev 2, 09/2004 Figure 2 Figure 3. ...
Page 2
... AN1984, Rev 2 SOIC16 1320A 482 482A M-Pak SOP SOP Ported Ported 24.0+/-0.3 32+/-0.3 32+/-0.3 7.2+/-0.1 11.3+/-0.1 12.0+/-0.2 13.2+/-0.1 18.9+/-0.1 18.8+/-0.2 10.5+/-0.1 6.4+/-0.1 13.8+/-0.1 4.0+/-0.1 4.0+/-0.1 4.0+/-0.1 1.5+/-0.05 1.5+/-0.1 1.75+/-0.1 1.75+/-0.1 1.75+/-0.1 22.2 min N/A N/A N/A 28.4+/-0.1 28.4+/-0.1 16.0+/-0.1 16.0+/-0.1 20.0+/-0.1 2.0+/-0.1 2.0+/-0.1 2.0+/-0.1 11 ...
Page 3
... Carrier Tape View A-A Figure 3. Carrier Tape AN1984, Rev 2 1320A 482 482A M-Pak SOP SOP Ported Ported 330+/-0.76 330+/-0.76 330+/-0.76 400 600 100 ...
Page 4
... Reel Bar Code Label Figure 5. Orientation of Small Outline Package Sensor Device Front View Sealing Tape Pocket Carrier Tape Figure 4. Reel Pin 1 User Direction of Feed AN1984, Rev 2 Plastic Reel Side View Pin 1 Corner Chamfer Sensor Products ...
Page 5
... C H PIN 1 IDENTIFIER M SOP PACKAGE CASE 482A-01 CASE 482A-01 ISSUE A ISSUE A AN1984, Rev 2 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006). 5. ALL VERTICAL SURFACES 5˚ TYPICAL DRAFT. ...
Page 6
... D A1 MPAK PACKAGE CASE 1320-02 CASE 1320-02 ISSUE A ISSUE A AN1984, Rev 2 NOTES: 1. DIMENSIONS ARE IN INCHES. 2. INTERPRET DIMENSIONS AND TOLERANCES PER ASME Y14.5M-1994. 3. DIMENSIONS "D" AND "E1" DO NOT INCLUDE MOLD FLASH OR PROTRUSION. MOLD FLASH OR PROTRUSION SHALL NOT EXCEED .006" PER SIDE ...
Page 7
... DETAIL MPAK PACKAGE CASE 1320A-02 CASE 1320A-02 ISSUE O ISSUE O AN1984, Rev 2 .014 GAGE PLANE θ L DETAIL E NOTES: 1. DIMENSIONS ARE IN INCHES. 2. INTERPRET DIMENSIONS AND TOLERANCES PER ASME Y14.5M-1994. 3. DIMENSIONS "D" AND "E1" DO NOT INCLUDE MOLD FLASH OR PROTRUSION. MOLD FLASH OR PROTRUSION SHALL NOT EXCEED .006" ...
Page 8
... PROTRUSION SHALL BE .008 INCHES MAXIMUM. 0.018 8X 5 0.014 0.004 GAGE PLANE 0.010 0.002 0.200 0.180 0.300 0.280 SSOP PACKAGE CASE 1317A-01 ISSUE A CASE 1317A-01 ISSUE A AN1984, Rev 2 .014 10˚ 0.048 0˚ 0.038 DETAIL E 0.300 0.280 3 BOTTOM VIEW DATE 07/18/01 Sensor Products Freescale Semiconductor ...
Page 9
... ALL VERTICAL SURFACES TO BE 5˚ MAXIMUM. 5. DIMENSION DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE .008 INCHES MAXIMUM. 0.019 5 8X 0.014 0.004 GAGE PLANE 0.010 0.002 DETAIL D SSOP PACKAGE CASE 1317-04 CASE 1317-04 ISSUE D ISSUE D AN1984, Rev 2 .014 10˚ 0.038 0˚ 0.048 DATE 09/23/03 9 ...
Page 10
... SSOP PACKAGE CASE 1352-02 CASE 1352-02 ISSUE A ISSUE A AN1984, Rev 2 1. CONTROLLING DIMENSION: INCH. 2. INTERPRET DIMENSIONS AND TOLERANCES PER ASME Y14.5M-1994. 3. DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS. MOLD FLASH AND PROTRUSIONS SHALL NOT EXCEED 0.006 PER SIDE. 4. ALL VERTICAL SURFACES TO BE 5˚ MAXIMUM. ...
Page 11
... Sensor Products Freescale Semiconductor AN1984, Rev 2 11 ...
Page 12
... Freescale Semiconductor Literature Distribution Center P.O. Box 5405 Denver, Colorado 80217 1-800-441-2447 or 303-675-2140 Fax: 303-675-2150 LDCForFreescaleSemiconductor@hibbertgroup.com AN1984 Rev. 2 09/2004 Information in this document is provided solely to enable system and software implementers to use Freescale Semiconductor products. There are no express or implied copyright licenses granted hereunder to design or fabricate any integrated circuits or integrated circuits based on the information in this document ...