LM3402MRX National Semiconductor, LM3402MRX Datasheet
LM3402MRX
Available stocks
Related parts for LM3402MRX
LM3402MRX Summary of contents
Page 1
... LEDs of varying number and type, LED dimming by pulse width modulation (PWM), broken/open LED protection, low-power shutdown and ther- mal shutdown complete the feature set. Typical Application © 2010 National Semiconductor Corporation LM3402/LM3402HV Features ■ Integrated 0.5A N-channel MOSFET ■ ...
Page 2
... Connection Diagrams 8-Lead Plastic MSOP-8 Package NS Package Number MUA08A Ordering Information Order Number Package Type LM3402MM LM3402MMX MSOP-8 LM3402HVMM LM3402HVMMX LM3402MR LM3402MRX PSOP-8 LM3402HVMR LM3402HVMRX Pin Descriptions Pin(s) Name Description BOOT MOSFET drive bootstrap pin 3 DIM Input for PWM dimming ...
Page 3
... Absolute Maximum Ratings (LM3402) (Note 1) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. VIN to GND BOOT to GND SW to GND BOOT to VCC BOOT to SW VCC to GND DIM to GND CS to GND RON to GND Junction Temperature Storage Temp ...
Page 4
... Absolute Maximum Ratings (LM3402HV) (Note 1) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. VIN to GND BOOT to GND SW to GND BOOT to VCC BOOT to SW VCC to GND DIM to GND CS to GND RON to GND Junction Temperature www ...
Page 5
Electrical Characteristics for +25°C. (Note 4) Limits appearing in boldface type apply over full Operating Temperature Range. Datasheet min/max A J specification limits are guaranteed by design, test, or statistical analysis. LM3402 Symbol Parameter SYSTEM PARAMETERS ...
Page 6
Symbol Parameter DIM COMPARATOR V Logic High IH V Logic Low IL I DIM Pull-up Current DIM-PU N-MOSFET AND DRIVER R Buck Switch On Resistance DS-ON V BOOT Under-voltage Lock-out DR-UVLO Threshold V BOOT Under-voltage Lock-out DR-HYS Hysteresis THERMAL SHUTDOWN ...
Page 7
Typical Performance Characteristics V vs Temperature (V REF LM3402HV (T REF IN Current Limit LM3402 ( 24V) IN 20192129 = 25°C) Current Limit vs Temperature (V A 20192131 = 25°C) Current ...
Page 8
100 kΩ 25° LM3402HV 25°C) A www.national.com , IN = 25°C) A 20192135 , IN 20192137 20192138 ...
Page 9
LM3402 O-MAX 25°C) A 20192140 LM3402HV O-MAX 25°C) A 20192142 LM3402 O-MIN 25° LM3402HV ...
Page 10
Block Diagram Application Information THEORY OF OPERATION The LM3402 and LM3402HV are buck regulators with a wide input voltage range, low voltage reference, and a fast output enable/disable function. These features combine to make them ideal for use as a ...
Page 11
The LM3402/02HV regulators should be operated in contin- uous conduction mode (CCM), where inductor current stays positive throughout the switching cycle. During steady-state operationin the CCM, the converter maintains a constant switching frequency, which can be selected using the follow- ...
Page 12
HIGH VOLTAGE BIAS REGULATOR The LM3402/02HV contains an internal linear regulator with a 7V output, connected between the VIN and the VCC pins. The VCC pin should be bypassed to the GND pin with a 0.1 µF ceramic capacitor connected ...
Page 13
LOW POWER SHUTDOWN The LM3402/02HV can be switched to a low power state ( µA) by grounding the RON pin with a signal-level SD MOSFET as shown in Figure 3. Low power MOSFETs like the 2N7000, 2N3904, or ...
Page 14
Design Considerations SWITCHING FREQUENCY Switching frequency is selected based on the tradeoffs be- tween efficiency (better at low frequency), solution size/cost (smaller at high frequency), and the range of output voltage that can be regulated (wider at lower frequency.) Many ...
Page 15
... Consequently, with a maxi- mum Vcc voltage of 7.4V, current will be observed in the LEDs if the total stack voltage is less than about forward current of several microamps. No current is observed if the stack voltage is above 6V, as shown Diode datasheets will also provide a typical D , which can ...
Page 16
DIM mode is also application de- pendent. It will not affect regular PWM dimming operation. The fix for this issue is extremely simple. Place a resistor from the SW pin to ground according to the chart below. ...
Page 17
FIGURE 7. CS Pin, Transient Path with Protection Adding a resistor in series with the CS pin causes the ob- served output LED current to shift very slightly. The reason for this is twofold: (1) the CS pin has about ...
Page 18
FIGURE 9. CS Pin with OVP, Transient Path with Protection VIN PIN PROTECTION The VIN pin also has an ESD structure from the pin to GND with a breakdown voltage of approximately 80V. Any transient that exceeds this voltage may ...
Page 19
LC tank circuit) and causes voltages at the VIN pin to rise well in excess of both V and the voltage at the module input connector as clamped IN by the input TVS. If the ...
Page 20
GENERAL COMMENTS REGARDING OTHER PINS Any pin that goes “off-board” through a connector should have series resistance of at least 1kΩ to 10kΩ in series with it to protect it from ESD or other transients. These series resistors limit the ...
Page 21
... The closest standard inductor value is 33 µH. Off-the-shelf inductors rated at 33 µH are available from many magnetics manufacturers. Inductor datasheets should contain three specifications which are used to select the inductor. The first of these is the aver- age current rating, which for a buck regulator is equal to the average load current ...
Page 22
To select the proper output capacitor the equation from Buck Regulators with Output Capacitors is re-arranged to yield the following: The target tolerance for LED ripple current is ± and the LED datasheet gives ...
Page 23
DCR loss the inductor DCR = 0. 0.096 = 11 Recirculating diode loss 119 mW D Current Sense Resistor Loss ...
Page 24
I = 0.35 + 0.027 = 377 mA L(PEAK) In the case of a short circuit across the LED array, the LM3402HV will continue to deliver rated current through the short but will reduce the output voltage to equal the ...
Page 25
DCR loss the inductor DCR = 0. 1.1 = 135 Recirculating diode loss Current Sense Resistor Loss ...
Page 26
ID Part Number U1 LM3402 L1 SLF7045T-330MR82 D1 CMHSH5-4 Cf VJ0805Y104KXXAT Cb VJ0805Y103KXXAT Cin C3216X7R1H105M Co C2012X7R1A225M Rsns ERJ6BQFR75V Ron CRCW08055902F ID Part Number U1 LM3402HV L1 DO5022P-684 D1 CMMSH1-100 Cf VJ0805Y104KXXAT Cb VJ0805Y103KXXAT Cin C4532X7R2A225M Rsns ERJ6BQFR56V Ron CRCW08051214F ...
Page 27
Physical Dimensions inches (millimeters) unless otherwise noted 8-Lead MSOP Package NS Package Number MUA08A 8-Lead PSOP Package NS Package Number MRA08B 27 www.national.com ...
Page 28
... For more National Semiconductor product information and proven design tools, visit the following Web sites at: www.national.com Products Amplifiers www.national.com/amplifiers Audio www.national.com/audio Clock and Timing www.national.com/timing Data Converters www.national.com/adc Interface www.national.com/interface LVDS www.national.com/lvds Power Management www.national.com/power Switching Regulators www.national.com/switchers LDOs www.national.com/ldo LED Lighting www ...