87C748 Philips Semiconductors, 87C748 Datasheet - Page 4

• Manufacturer Part Number: 87C748
• Description: 80C51 8-bit microcontroller family 2K/64 OTP/ROM/ low pin count
• Manufacturer: Philips Semiconductors

1. When P0.2 is at or close to 0 volts, it may affect the internal ROM operation. It is recommended that P0.2 be tied to V
1. Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only and
2. This product includes circuitry specifically designed for the protection of its internal devices from the damaging effects of excessive static
Philips Semiconductors
PIN DESCRIPTIONS
NOTE:
ABSOLUTE MAXIMUM RATINGS
NOTES:
1999 Apr 15
MNEMONIC
V
V
P0.0–P0.2
P1.0–P1.7
P3.0–P3.7
RST
X1
X2
SS
CC
80C51 8-bit microcontroller family
2K/64 OTP/ROM, low pin count
Storage temperature range
Voltage from V
Voltage from any pin to V
Power dissipation
Voltage on V
Maximum I
(e.g. 2kW).
functional operation of the device at these or any conditions other than those described in the AC and DC Electrical Characteristics section
of this specification is not implied.
charge. Nonetheless, it is suggested that conventional precautions be taken to avoid applying greater than the rated maxima.
OL
PP
SSOP
13–20
23–21
per I/O pin
DIP/
5–1,
8–6
CC
12
24
18
19
20
11
10
6
7
8
9
pin to V
PIN NO.
to V
SS
15–20,
6, 4–1,
23, 24
27–25
LCC
SS
9–7
14
28
20
23
24
11
13
12
7
8
9
SS
(except V
TYPE
N/A
I/O
I/O
I/O
O
I
I
I
I
I
I
I
I
I
PP
Circuit Ground Potential
Supply voltage during normal, idle, and power-down operation.
Port 0: Port 0 is a 3-bit open-drain, bidirectional port. Port 0 pins that have 1s written to them float,
and in that state can be used as high-impedance inputs. These pins are driven low if the port register
bit is written with a 0. The state of the pin can always be read from the port register by the program.
P0.0 and P0.1 are open drain bidirectional I/O pins. While these differ from “standard TTL”
characteristics, they are close enough for the pins to still be used as general-purpose I/O. Port 0
also provides alternate functions for programming the EPROM memory as follows:
V
OE/PGM (P0.1) – Input which specifies verify mode (output enable) or the program mode.
OE/PGM = 1 output enabled (verify mode).
OE/PGM = 0 program mode.
ASEL (P0.0) – Input which indicates which bits of the EPROM address are applied to port 3.
ASEL = 0 low address byte available on port 3.
ASEL = 1 high address byte available on port 3 (only the three least significant bits are used).
Port 1: Port 1 is an 8-bit bidirectional I/O port with internal pull-ups. Port 1 pins that have 1s written
to them are pulled high by the internal pull-ups and can be used as inputs. As inputs, port 1 pins
that are externally pulled low will source current because of the internal pull-ups. (See DC Electrical
Characteristics: I
accepts as inputs the value to program into the selected address during the program mode. Port 1
also serves the special function features of the 80C51 family as listed below:
INT0 (P1.5): External interrupt.
INT1 (P1.6): External interrupt.
T0 (P1.7): Timer 0 external input.
Port 3: Port 3 is an 8-bit bidirectional I/O port with internal pull-ups. Port 3 pins that have 1s written
to them are pulled high by the internal pull-ups and can be used as inputs. As inputs, port 3 pins
that are externally being pulled low will source current because of the pull-ups. (See DC Electrical
Characteristics: I
programmed (or verified). The 11-bit address is multiplexed into this port as specified by P0.0/ASEL.
Reset: A high on this pin for two machine cycles while the oscillator is running, resets the device.
An internal diffused resistor to V
V
the device in the programming state allowing programming address, data and V
programming or verification purposes. The RESET serial sequence must be synchronized with the
X1 input.
Crystal 1: Input to the inverting oscillator amplifier and input to the internal clock generator circuits.
X1 also serves as the clock to strobe in a serial bit stream into RESET to place the device in the
programming state.
Crystal 2: Output from the inverting oscillator amplifier.
)
1, 2
PP
CC
PARAMETER
. After the device is reset, a 10-bit serial sequence, sent LSB first, applied to RESET, places
(P0.2) – Programming voltage input. (See Note 1).
IL
IL
). Port 3 also functions as the address input for the EPROM memory location to be
). Port 1 serves to output the addressed EPROM contents in the verify mode and
4
SS
permits a power-on RESET using only an external capacitor to
NAME AND FUNCTION
–0.5 to V
–65 to +150
–0.5 to +6.5
0 to +13.0
RATING
83C748/87C748
1.0
10
CC
Preliminary specification
+ 0.5
CC
PP
via a small pull-up
to be applied for
UNIT
mA
W
V
V
V
C