83C196KB Intel Corporation, 83C196KB Datasheet
83C196KB
Related parts for 83C196KB
83C196KB Summary of contents
Page 1
... The 8XC196KB has a maximum guaranteed frequency of 12 MHz The 8XC196KB16 has a maximum guaran- teed frequency of 16 MHz All references to the 80C196KB also refer to the 80C196KB16 83C196KB Rxxx 87C196KB and 87C196KB16 unless otherwise noted The ROM device does not have a speed indicator at the ...
Page 2
Figure 1 8XC196KB Block Diagram 2 270909 – 1 ...
Page 3
PROCESS INFORMATION This device is manufactured on P629 0 and 629 1 a CHMOS III-E process Additional process and reli- ability information is available in Intel’s Components Quality and Reliability Handbook Order Number 210997 EXAMPLE N87C196KB16 is 68-Lead OTPROM 16 ...
Page 4
... The above pin out diagram applies to the OTP (87C196KB) device The OTP device uses all of the programming pins shown above The ROM (83C196KB) device only uses programming pins AINC PALE PMODE n and PROG The ROMless (80C196KB) doesn’t use any of the programming pins 4 270909 – ...
Page 5
... The above pin out diagram applies to the OTP (87C196KB) device The OTP device uses all of the programming pins shown above The ROM (83C196KB) device only uses programming pins AINC PALE PMODE n and PROG The ROMless (80C196KB) doesn’t use any of the programming pins ...
Page 6
PIN DESCRIPTIONS Symbol V Main supply voltage (5V Digital circuit ground (0V) There are multiple Reference voltage for the A D converter (5V) V REF portion of the A D converter and the ...
Page 7
PIN DESCRIPTIONS (Continued) Symbol Port 0 8-bit high impedance input-only port Three pins can be used as digital inputs and or as analog inputs to the on-chip A D converter Port 1 8-bit quasi-bidirectional I O port These pins are ...
Page 8
ELECTRICAL CHARACTERISTICS ABSOLUTE MAXIMUM RATINGS Ambient Temperature Under Bias Storage Temperature Voltage On Any Pin (1) Power Dissipation NOTE 1 Power dissipation is ...
Page 9
DC CHARACTERISTICS (Continued) Symbol Description I Logical 0 Input Current in Reset IL1 BHE Logical 0 Input Current in Reset IL2 ALE RD INST I Logical 1 Input Current IH1 on NMI Pin Hyst Hysteresis on ...
Page 10
AC CHARACTERISTICS Test Conditions Capacitive load on all pins The system must meet these specifications to work with the 87C196KB Symbol Description T Address Valid to READY Setup AVYV T NonREADY Time YLYH T READY Hold after CLKOUT ...
Page 11
AC CHARACTERISTICS (Continued) Test Conditions Capacitive load on all pins The 87C196KB will meet these specifications Symbol Description F Frequency on XTAL1 12 MHz XTAL F Frequency on XTAL1 16 MHz XTAL MHz OSC XTAL T ...
Page 12
System Bus Timings 12 270909 – 6 ...
Page 13
READY Timings (One Wait State) Buswidth Bus Timings 8XC196KB 8XC196KB16 270909 – 7 270909 – ...
Page 14
HOLD HLDA Timings Symbol Description T HOLD Setup HVCH T CLKOUT Low to HLDA Low CLHAL T CLKOUT Low to BREQ Low CLBRL T HLDA Low to Address Float HALAZ T HLDA Low to BHE INST RD WR ...
Page 15
EXTERNAL CLOCK DRIVE Symbol Parameter 1 T Oscillator Frequency 12 MHz XLXL 1 T Oscillator Frequency 16 MHz XLXL T Oscillator Period 12 MHz XLXL T Oscillator Period 16 MHz XLXL T High Time XHXX T Low Time XLXX T ...
Page 16
EXPLANATION OF AC SYMBOLS Each symbol is two pairs of letters prefixed by ‘‘T’’ for time The characters in a pair indicate a signal and its condition respectively Symbols represent the time between the two signal condition points ...
Page 17
A D CHARACTERISTICS At a clock speed of 6 MHz or less the clock prescal- er should be disabled This is accomplished by set- ting IOC2 higher frequencies (greater than 6 MHz) the clock prescaler ...
Page 18
OTPROM SPECIFICATIONS OTPROM PROGRAMMING OPERATING CONDITIONS Symbol T Ambient Temperature During Programming A ( Supply Voltages During Programming CC PD REF V Programming Mode Supply Voltage EA V EPROM Programming Supply Voltage PP (3) V ...
Page 19
DC OTPROM PROGRAMMING CHARACTERISTICS Symbol Description I V Supply Current (When Programming NOTE Do not apply V until V is stable and within specifications and the oscillator clock has stabilized or the device may damaged ...
Page 20
SLAVE PROGRAMMING MODE TIMING IN DATA PROGRAM MODE WITH REPEATED PROG PULSE AND AUTO INCREMENT 20 270909 –17 ...
Page 21
... The following differences exist between this data sheet (270909-004) and (270909-003) 1 The ROM (80C196KB) and (83C196KB) were combined with this data sheet resulting in no specification differences 2 The description of the prescalar bit for the A D has been enhanced 3 T MIN was 15 ns (270909-003) Now ...
Page 22
The following differences exist between (-003) and version (-002) 1 The 12 MHz and 16 MHz devices were com- bined in this data sheet The 87C196KB 12 MHz only data sheet (272035-001) is now obsolete 2 Changes were ...