MC74HC589 Motorola, MC74HC589 Datasheet
MC74HC589
Available stocks
Related parts for MC74HC589
MC74HC589 Summary of contents
Page 1
... Data can also be loaded serially (see Function Table). The shift register output three–state output, allowing this device to be used in bus–oriented systems. The HC589 directly interfaces with the Motorola SPI serial data port on CMOS MPUs and MCUs. Output Drive Capability: 15 LSTTL Loads ...
Page 2
... Current (per Package) Î Î Î Î Î Î Î Î Î Î Î Î Î NOTE: Information on typical parametric values can be found in Chapter 2 of the Motorola High–Speed CMOS Data Book (DL129/D). MOTOROLA Î Î Î Î Î Î Î Î Î ...
Page 3
... NOTES: 1. For propagation delays with loads other than 50 pF, see Chapter 2 of the Motorola High–Speed CMOS Data Book (DL129/D). 2. Information on typical parametric values can be found in Chapter 2 of the Motorola High–Speed CMOS Data Book (DL129/D). ...
Page 4
... NOTE: Information on typical parametric values can be found in Chapter 2 of the Motorola High–Speed CMOS Data Book (DL129/D). Output Serial Shift/ ...
Page 5
... V CC GND * Includes all probe and jig capacitance 3–5 MC54/74HC589 1/f max 50% GND t PLH t PHL 50% 50% GND t PLH t PHL 50% Figure 4. DATA VALID V CC 50% GND 50% Figure 6. TEST POINT OUTPUT DEVICE UNDER TEST Figure 8. Test Circuit MOTOROLA ...
Page 6
... Shift register mode control. When a high level is applied to this pin, the shift register is allowed to serially shift data. When a low level is applied to this pin, the shift register ac- cepts parallel data from the data latch. MOTOROLA TEST CIRCUIT TEST POINT CONNECT WHEN ...
Page 7
... DL129 — Rev 6 TIMING DIAGRAM SERIAL SHIFT LOAD LATCH PARALLEL LOAD SHIFT REGISTER 3–7 MC54/74HC589 SERIAL SERIAL SHIFT SHIFT PARALLEL LOAD, LATCH AND SHIFT REGISTER MOTOROLA ...
Page 8
... PARALLEL DATA 2 C INPUTS *NOTE: Stages C thru G (not shown in detail) are identical to stages A and B above. MOTOROLA LOGIC DETAIL STAGE A Q STAGE B Q STAGE C* STAGE D* STAGE E* STAGE F* STAGE G* STAGE H Q 3– ...
Page 9
... PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. MILLIMETERS INCHES DIM MIN MAX MIN MAX F A 0.386 0.393 9.80 10.00 B 3.80 4.00 0.150 0.157 C 1.35 1.75 0.054 0.068 D 0.35 0.49 0.014 0.019 F 0.40 1.25 0.016 0.049 1.27 BSC 0.050 BSC G J 0.19 0.25 0.008 0.009 K 0.10 0.25 0.004 0.009 0.229 0.244 P 5.80 6.20 R 0.25 0.50 0.010 0.019 MOTOROLA ...
Page 10
... Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters can and do vary in different applications. All operating parameters, including “ ...