74ALVC574D Philips Semiconductors, 74ALVC574D Datasheet
74ALVC574D
Related parts for 74ALVC574D
74ALVC574D Summary of contents
Page 1
DATA SHEET 74ALVC574 Octal D-type flip-flop; positive edge-trigger; 3-state Product specification INTEGRATED CIRCUITS 2002 Mar 04 ...
Page 2
... Philips Semiconductors Octal D-type flip-flop; positive edge-trigger; 3-state FEATURES Wide supply voltage range from 1.65 to 3.6 V Complies with JEDEC standard: JESD8-7 (1.65 to 1.95 V) JESD8-5 (2.3 to 2.7 V) JESD8B/JESD36 (2.7 to 3.6 V). 3.6 V tolerant inputs/outputs CMOS low power consumption Direct interface with TTL levels (2.7 to 3.6 V) Power-down mode Latch-up performance exceeds 250 mA ...
Page 3
... Philips Semiconductors Octal D-type flip-flop; positive edge-trigger; 3-state ORDERING INFORMATION TYPE NUMBER 74ALVC574D 74ALVC574PW FUNCTION TABLE See note 1. OPERATING MODES Load and read register Latch and read register Note HIGH voltage level HIGH voltage level one set-up time prior to the HIGH-to-LOW CP transition; ...
Page 4
... Philips Semiconductors Octal D-type flip-flop; positive edge-trigger; 3-state handbook, halfpage 574 GND 10 MNA444 Fig.1 Pin configuration. handbook, halfpage MNA446 Fig.3 IEE/IEC logic symbol. ...
Page 5
... Philips Semiconductors Octal D-type flip-flop; positive edge-trigger; 3-state handbook, full pagewidth FF1 FF2 2002 Mar FF3 FF4 Fig.5 Logic diagram. 5 Product specification 74ALVC574 ...
Page 6
... Philips Semiconductors Octal D-type flip-flop; positive edge-trigger; 3-state RECOMMENDED OPERATING CONDITIONS SYMBOL PARAMETER V supply voltage CC V input voltage I V output voltage O T operating ambient temperature amb input rise and fall times r f LIMITING VALUES In accordance with the Absolute Maximum Rating System (IEC 60134); voltages are referenced to GND (ground = 0 V). ...
Page 7
... Philips Semiconductors Octal D-type flip-flop; positive edge-trigger; 3-state DC CHARACTERISTICS At recommended operating conditions; voltages are referenced to GND (ground = 0 V). SYMBOL PARAMETER V HIGH-level input IH voltage V LOW-level input IL voltage V LOW-level output OL voltage V HIGH-level output OH voltage I input leakage I current I 3-state output OZ OFF-state current I power OFF ...
Page 8
... Philips Semiconductors Octal D-type flip-flop; positive edge-trigger; 3-state AC CHARACTERISTICS SYMBOL PARAMETER t /t propagation delay PHL PLH t /t 3-state output enable time PZH PZL 3-state output disable time PHZ PLZ clock pulse with HIGH or LOW ...
Page 9
... Philips Semiconductors Octal D-type flip-flop; positive edge-trigger; 3-state AC WAVEFORMS handbook, full pagewidth CP input Q n output 1.65 to 1. 2.3 to 2 2.7 V 1.5 V 3.0 to 3.6 V 1.5 V Fig.6 Input D to output Q n 2002 Mar 04 1/f max GND PHL V M INPUT ...
Page 10
... Philips Semiconductors Octal D-type flip-flop; positive edge-trigger; 3-state handbook, full pagewidth CP input D n input Q n output 1.65 to 1. 2.3 to 2 2.7 V 1.5 V 3.0 to 3.6 V 1.5 V The shaded areas indicate when the input is permitted to change for predictable output performance. 2002 Mar ...
Page 11
... Philips Semiconductors Octal D-type flip-flop; positive edge-trigger; 3-state handbook, full pagewidth OE input Q n output LOW-to-OFF OFF-to-LOW Q n output HIGH-to-OFF OFF-to-HIGH 1.65 to 1. 2.3 to 2 2.7 V 1.5 V 3.0 to 3.6 V 1.5 V 2002 Mar GND t PLZ ...
Page 12
... Philips Semiconductors Octal D-type flip-flop; positive edge-trigger; 3-state handbook, full pagewidth 1. 2 2 3.0 to 3 Load resistor Load capacitance including jig and probe capacitance Termination resistance should be equal to the output impedance Z ...
Page 13
... Philips Semiconductors Octal D-type flip-flop; positive edge-trigger; 3-state PACKAGE OUTLINES SO20: plastic small outline package; 20 leads; body width 7 pin 1 index 1 e DIMENSIONS (inch dimensions are derived from the original mm dimensions) A UNIT max. 0.30 2.45 mm 2.65 0.25 0.10 2.25 0.012 0.096 inches ...
Page 14
... Philips Semiconductors Octal D-type flip-flop; positive edge-trigger; 3-state TSSOP20: plastic thin shrink small outline package; 20 leads; body width 4 pin 1 index 1 e DIMENSIONS (mm are the original dimensions) A UNIT max. 0.15 0.95 mm 1.10 0.25 0.05 0.80 Notes 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. ...
Page 15
... Philips Semiconductors Octal D-type flip-flop; positive edge-trigger; 3-state SOLDERING Introduction to soldering surface mount packages This text gives a very brief insight to a complex technology. A more in-depth account of soldering ICs can be found in our “Data Handbook IC26; Integrated Circuit Packages” (document order number 9398 652 90011). ...
Page 16
... Philips Semiconductors Octal D-type flip-flop; positive edge-trigger; 3-state Suitability of surface mount IC packages for wave and reflow soldering methods PACKAGE BGA, LFBGA, SQFP, TFBGA HBCC, HLQFP, HSQFP, HSOP, HTQFP, HTSSOP, SMS (3) PLCC , SO, SOJ LQFP, QFP, TQFP SSOP, TSSOP, VSO Notes 1. All surface mount (SMD) packages are moisture sensitive. Depending upon the moisture content, the maximum temperature (with respect to time) and body size of the package, there is a risk that internal or external package cracks may occur due to vaporization of the moisture in them (the so called popcorn effect) ...
Page 17
... Mar 04 (2) This data sheet contains data from the objective specification for product development. Philips Semiconductors reserves the right to change the specification in any manner without notice. This data sheet contains data from the preliminary specification. Supplementary data will be published at a later date. Philips Semiconductors reserves the right to change the specifi ...
Page 18
... Philips Semiconductors Octal D-type flip-flop; positive edge-trigger; 3-state 2002 Mar 04 NOTES 18 Product specification 74ALVC574 ...
Page 19
... Philips Semiconductors Octal D-type flip-flop; positive edge-trigger; 3-state 2002 Mar 04 NOTES 19 Product specification 74ALVC574 ...
Page 20
... Philips Semiconductors – a worldwide company Contact information For additional information please visit http://www.semiconductors.philips.com. For sales offices addresses send e-mail to: sales.addresses@www.semiconductors.philips.com. © Koninklijke Philips Electronics N.V. 2002 All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. ...