NCP5602 ON Semiconductor, NCP5602 Datasheet
NCP5602
Related parts for NCP5602
NCP5602 Summary of contents
Page 1
... NCP5602 High Efficiency Ultra Small Thinnest White LED Driver The NCP5602 product is a dual output LED driver dedicated to the LCD display backlighting. The built−in DC−DC converter is based on a high efficient charge pump structure with operating mode 1x and 1.5x. It provides a peak 87% efficiency together with a 0 ...
Page 2
... Vbat C3 11 GND 1 mF/6.3 V SCL 6 DIGITAL CONTROL SDA 5 Vbat R1 GND 4 100 k ANALOG CONTROL 1 GND OVERTEMPERATURE NCP5602 C2 C1 220 nF 220 CHARGE PUMP DC−DC CONVERTER OVERVOLTAGE Vbat Q1 Q2 GND ICON Figure 2. Simplified Block Diagram http://onsemi.com GND 1 mF/6.3 V Vout ...
Page 3
... POWER 1. Using low ESR ceramic capacitor is mandatory to optimize the Charge Pump efficiency. 2. Total DC−DC output current is limited to 60 mA. NCP5602 Description This pin is the GROUND signal for the analog and digital blocks and must be connected to the system ground. This pin is the GROUND reference for the DC− ...
Page 4
... This device series contains ESD protection and exceeds the following tests: Human Body Model (HBM) "2.0 kV per JEDEC standard: JESD22−A114. Machine Model (MM) "200V per JEDEC standard: JESD22−A115. 4. The maximum package power dissipation limit must not be exceeded. 5. Moisture Sensitivity Level (MSL): 1 per IPC/JEDEC standard: J−STD−020A. NCP5602 Symbol V BAT Vout ...
Page 5
... InputI2C Clock Frequency (Note 8) Positive Going Input High Voltage Threshold, SCL, SDA Signals Negative Going Input High Voltage Threshold, SCL, SDA Signals 8. Parameter not tested in production, guaranteed by design. NCP5602 = +25°C, Min & Max values are referenced −40°C to +85°C ambient A Pin Symbol ...
Page 6
... REF GND Figure 3. Basic Reference Current Source Load Connection The NCP5602 chip is capable to drive the two LED simultaneously, as depicted in Figure 1, but the load can be arranged to accommodate one or two LED if necessary in the application (see Figure 4). In this case, the two current mirrors can be connected in parallel to drive a single power full LED, thus yielding 60 mA current capability in a single (eq ...
Page 7
... Finally, an external network can be connected across Vout and ground , but the current through such network will not be regulated by the NCP5602 chip (see Figure 5). On I2C Protocol The standard I2C protocol is used to transfer the data from the MCU to the NCP5602. Leaving aside the ...
Page 8
... The physical address of the NCP5602 is 1001 111X, the X being the Read/Write identifier as defined by the I2C specification. Since the NCP5602 does not return data, the first byte of the I2C frame shall be 1001 1110 ($9E) as depicted in Table 2. Table 1. NCP5602 Physical I2C Address B7 B6 ...
Page 9
... Figure 11, illustrate the programming sequence to activate the ICON. Figure 11. ICON Programming Sequence VCC 220 nF/63 V 220 nF/ Vbat 6 SCL 5 SDA 4 IREF 1 GND U1 NCP5602 Z1 GND GND Figure 12. Demo Board Schematic Diagram http://onsemi.com GND 4.7 mF/ Vout Vout D1 2 LED1 LED1 LWY8S ...
Page 10
... NCP5602 Figure 13. LED Current Matching Figure 14. Efficiency as a Function of V http://onsemi.com bat ...
Page 11
... NCP5602 Figure 15. NCP5602 Demo Board http://onsemi.com 11 ...
Page 12
... PAD AS WELL AS THE TERMINALS. MILLIMETERS DIM MIN MAX A 0.50 0.60 A1 0.00 0.05 b 0.15 0.25 D 2.00 BSC D2 0.80 1.00 E 2.00 BSC E2 0.55 0.65 e 0.40 BSC K 0.25 −−− L 0.30 0.50 L1 0.40 0.60 SOLDERING FOOTPRINT* 0.66 2.30 12X 0.23 1 0.93 11X 0.56 0.63 DIMENSIONS: MILLIMETERS ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative NCP5602/D 0.40 PITCH 0.91 ...