NCP1393B ON Semiconductor, NCP1393B Datasheet
NCP1393B
Available stocks
Related parts for NCP1393B
NCP1393B Summary of contents
Page 1
... High-Voltage Half-Bridge Driver with Inbuilt Oscillator The NCP1393B is a self−oscillating high voltage MOSFET driver primarily tailored for the applications using half−bridge topology. Due to its proprietary high−voltage technology, the driver accepts bulk voltages up to 600 V. Operating frequency of the driver can be adjusted from 25 kHz to 250 kHz using a single resistor. Adjustable brown− ...
Page 2
Rbo1 www.DataSheet4U.com AC OUTPUT + PFC FRONT STAGE Cbulk Rf Rbo2 M1 Dboot Cboot VCC Vboot Rt Mupper Bo HB GND Mlower M2 NCP1393 Rfstart Rfmax CSS Figure 1. Typical Application Example http://onsemi.com 2 DC OUTPUT + ...
Page 3
V DD www.DataSheet4U.com V ref PFC Delay (100ms ref V DD PON V RESET Management V CC Clamp TSD − 20ms + Filter + V latch ref − BO ...
Page 4
PIN FUNCTION DESCRIPTION Pin # Pin Name Function www.DataSheet4U.com 1 V Supplies the Driver Timing Resistor 3 BO Brown−Out 4 GND IC Ground 5 M Low−Side Driver Output lower 6 HB Half−Bridge Connection 7 M High−Side Driver ...
Page 5
ELECTRICAL CHARACTERISTICS unless otherwise noted) CC Characteristic www.DataSheet4U.com SUPPLY SECTION Turn−On Threshold Level, V Going Up CC Minimum Operating Voltage after Turn−On Startup Voltage on the Floating Section Cutoff Voltage on the Floating Section V Level ...
Page 6
TEMPERATURE (°C) Figure 3. V 8.85 8.80 8.75 8.70 8.65 8.60 8.55 −40 − TEMPERATURE (°C) Figure 5. V BOOTon ...
Page 7
TEMPERATURE (°C) Figure 9. F 45.0 40.0 35.0 30.0 25.0 20.0 15.0 10.0 5.0 0.0 −40 − TEMPERATURE (°C) Figure 11. I ...
Page 8
TEMPERATURE (°C) Figure 15. PFC 1.015 1.014 1.013 1.012 1.011 1.010 1.009 1.008 1.007 −40 − TEMPERATURE (°C) Figure 17. ...
Page 9
The NCP1393 is primarily intended to drive low cost half−bridge applications and www.DataSheet4U.com half−bridge applications. The IC includes several features that help the designer to cope with resonant SPMS design. All features are described thereafter: • Wide Operating Frequency Range: ...
Page 10
The internal timing capacitor Ct is charged by current which is proportional to the current flowing out from the Rt pin. The discharging current I is applied when voltage DT www.DataSheet4U.com on this capacitor reaches 2.5 V. The output drivers ...
Page 11
V bulk www.DataSheet4U.com R upper BO R lower Figure 23. The internal Brown−Out Configuration with an Offset Current Sink A resistive divider made of R upper portion of the HV rail on Pin 3. Below the turn−on level, the 18.2 ...
Page 12
Figure 24. Simulation Results for 350/250 ON/OFF Brown−Out Levels Figure 25. BO Input Functionality − V < V < V bulk2 bulk bulk1 http://onsemi.com 12 ...
Page 13
Figure 26. BO Input Functionality −V Figure 27. BO Input Functionality − V < V < PFC Start Follows bulk2 bulk bulk1 > V bulk bulk1 http://onsemi.com 13 ...
Page 14
Figure 28. BO Input Functionality − V The I current sink is turned ON for 50 ms after any BO controller restart to let the BO input voltage stabilize (there can be connected big capacitor to the BO input ...
Page 15
C capacitor that is refilled by external boot bootstrap diode. www.DataSheet4U.com Pulse Trigger DEAD TIME B A from latch high if OK Figure 30. The Internal High−Voltage Section of the NCP1393 The A and B outputs are ...
Page 16
... *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. The products described herein (NCP1393), may be covered by one or more of the following U.S. patents; 6,097, 075; 7176723; 6,362, other patents pending. ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC) ...