TDA7295V ST Microelectronics, TDA7295V Datasheet
TDA7295V
Available stocks
Related parts for TDA7295V
TDA7295V Summary of contents
Page 1
... July 1999 MULTIPOWER BCD TECHNOLOGY Multiwatt 15 ORDERING NUMBER: TDA7295V to the high out current capability it is able to sup- ply the highest power into both 4 even in presence of poor supply regulation, with high Supply Voltage Rejection. The built in muting function with turn on delay simplifies the remote operation avoiding switching on-off noises ...
Page 2
TDA7295 PIN CONNECTION (Top view) BLOCK DIAGRAM ABSOLUTE MAXIMUM RATINGS Symbol V Supply Voltage S I Output Peak Current O P Power Dissipation tot case T Operating Ambient Temperature Range Storage and ...
Page 3
THERMAL DATA Symbol R Thermal Resistance Junction-case th j-case ELECTRICAL CHARACTERISTICS (Refer to the Test Circuit kHz; unless otherwise specified. g amb Symbol Parameter V Operating Supply Range ...
Page 4
TDA7295 Figure 2: P.C.B. and components layout of the circuit of figure 1. (1:1 scale) Note: The Stand-by and Mute functions can be referred either to GND or -VS. On the P.C.B. is possible to set both the configuration through ...
Page 5
APPLICATION SUGGESTIONS (see Test and Application Circuits of the Fig. 1) The recommended values of the external components are those shown on the application circuit of Fig- ure 1. Different values can be used; the following table can help the ...
Page 6
TDA7295 TYPICAL CHARACTERISTICS (Application Circuit of fig 1 unless otherwise specified) Figure 3: Output Power vs. Supply Voltage. Figure 5: Output Power vs. Supply Voltage Figure 7: Distortion vs. Frequency 6/13 Figure 4: Distortion vs. Output Power Figure 6: Distortion ...
Page 7
TYPICAL CHARACTERISTICS (continued) Figure 9: Quiescent Current vs. Supply Voltage Figure 11: Mute Attenuation vs. V pin10 Figure 13: Power Dissipation vs. Output Power Figure10: SupplyVoltage Rejection vs. Frequency Figure 12: St-by Attenuation vs. V pin9 Figure 14: Power Dissipation ...
Page 8
TDA7295 INTRODUCTION In consumer electronics, an increasing demand has arisen for very high power monolithic audio amplifiers able to match, with a low cost the per- formance obtained from the best discrete de- signs. The task of realizing this linear ...
Page 9
Figure 16: Turn ON/OFF Suggested Sequence +Vs (V) +35 -35 - (mV) V ST-BY 5V PIN #9 (V) V MUTE 5V PIN #10 ( (mA) V OUT (V) OFF ST-BY In addition to the overload protection ...
Page 10
TDA7295 BRIDGE APPLICATION Another application suggestion is the BRIDGE configuration, where two TDA7295 are used, as shown by the schematic diagram of figure 25. In this application, the value of the load must not be lower than 8 Ohm for ...
Page 11
Figure 19: Frequency Response of the Bridge Application Figure 21: Distortion vs. Output Power Figure 20: Distortion vs. Output Power TDA7295 11/13 ...
Page 12
TDA7295 mm DIM. MIN. TYP. MAX. MIN 2. 0.49 0.55 0.019 F 0.66 0.75 0.026 G 1.02 1.27 1.52 0.040 0.050 G1 17.53 17.78 18.03 0.690 0.700 H1 19.6 0.772 H2 20.2 ...
Page 13
Informationfurnishedisbelievedtobeaccurateandreliable.However,STMicroelectroni csassumesnoresponsibilityfortheconsequences of use of such informationnor for any infringementof patentsor otherrights of third parties which may result from its use. No license is grantedbyimplicationorotherwiseunderanypatentorpatent rightsof STMicroelectronics.Specificationmentionedinthispublicationare subjecttochangewithoutnotice.Thi spublicationsupersedesandreplacesallinformati on previously supplied. S TMicroelectronics products arenotauthorizedforuseascriticalcomponentsinlifesupportdevicesorsystemswithoutexpresswrittenapproval o fSTMicroelectronics. TheSTlogoisaregisteredtrademarkofSTMicroelectronics 1999 ...