MCP3905A-I/SSRA1 Microchip Technology, MCP3905A-I/SSRA1 Datasheet - Page 2

• Manufacturer Part Number: MCP3905A-I/SSRA1
• Description: Energy Meter IC, Gain 1:16, 500:1 Dynamic Range, -40C to +85C, 24-SSOP 208mil, TUBE
• Manufacturer: Microchip Technology

MCP3905A/05L/06A
1.0
Absolute Maximum Ratings †
V
Digital inputs and outputs w.r.t. A
Analog input w.r.t. A
V
Storage temperature .....................................-65°C to +150°C
Ambient temp. with power applied ................-65°C to +125°C
Soldering temperature of leads (10 seconds) ............. +300°C
ESD on the analog inputs (HBM,MM) .................5.0 kV, 500V
ESD on all other pins (HBM,MM) ........................5.0 kV, 500V
DS22011A-page 2
ELECTRICAL CHARACTERISTICS
Electrical Specifications: Unless otherwise indicated, all parameters apply at AV
Internal V
Overall Measurement Accuracy
Energy Measurement Error
No-Load Threshold/
Minimum Load
Phase Delay Between
Channels
AC Power Supply Rejection
(output frequency variation)
DC Power Supply Rejection
(output frequency
variation)
System Gain Error
ADC/PGA Specifications
Offset Error
Gain Error Match
Internal Voltage Reference
Voltage
Tolerance
Tempco
Note 1:
DD
REF
...................................................................................7.0V
input w.r.t. A
2:
3:
4:
5:
6:
7:
ELECTRICAL
CHARACTERISTICS
Parameter
REF
Measurement error = (Energy Measured By Device - True Energy)/True Energy * 100%. Accuracy is
measured with signal (±660 mV) on Channel 1. F
See typical performance curves for higher frequencies and increased dynamic range.
Does not include internal V
measured output frequency and expected transfer function.
Percent of HF
50 Hz, CH2 = 100 mVRMS @ 50 Hz, AV
Error applies down to 60 degree lead (PF = 0.5 capacitive) and 60 degree lag (PF = 0.5 inductive).
Refer to Section 4.0 “Device Overview” for complete description.
Specified by characterization, not production tested.
1 MCLK period at 3.58 MHz is equivalent to less than <0.005 degrees at 50 or 60 Hz.
, HPF turned on (AC mode), A
GND
GND
............................... -0.6V to V
..................................... ....-6V to +6V
OUT
GND
output frequency variation; Includes external V
DC PSRR
AC PSRR
........ -0.6V to V
Sym
NLT
V
E
OS
REF
. Gain = 1, CH0 = 470 mVDC, CH1 = 660 mVDC, difference between
GND
Min
—
—
—
—
—
—
—
—
—
—
—
—
DD
DD
, D
+0.6V
+0.6V
GND
DD
0.0015
Typ.
0.01
0.01
0.1
0.1
0.5
2.4
±2
15
—
3
2
= 5V + 1V
= 0V, MCLK = 3.58 MHz; T
OUT0
1/MCLK
† Notice: Stresses above those listed under "Maximum
Ratings" may cause permanent damage to the device. This is
a stress rating only and functional operation of the device at
those or any other conditions above those indicated in the
operation listings of this specification is not implied. Exposure
to maximum rating conditions for extended periods may affect
device reliability.
Max
—
—
—
—
—
10
—
—
—
—
5
, F
pp
OUT1
@ 100 Hz. DC PSRR: 5V ±500 mV
% F
% F
% F
% F
% F
% F
% F
ppm/°C
Units
pulse outputs. Valid from 45 Hz to 65 Hz.
Max
mV
%
V
s
OUT
OUT
OUT
OUT
OUT
OUT
OUT
REF
= 2.5V, CH1 = 100 mVRMS @
Channel 0 swings 1:500 range,
MCP3905A, MCP3905L only
(Note 1, Note 4)
Channel 0 swings 1:1000 range,
MCP3906A only (Note 1, Note 4)
Disabled when F2, F1, F0 = 0, 1, 1
(Note 5, Note 6)
HPF = 0 and 1, < 1 MCLK
(Note 4, Note 6, Note 7)
F2, F1, F0 = 0, 1, 1 (Note 3)
HPF = 1, Gain = 1 (Note 3)
(Note 2, Note 5)
Referred to Input
(Note 5)
A
DD
= -40°C to +85°C.
= DV
© 2006 Microchip Technology Inc.
DD
= 4.5V – 5.5V,
Comment