AAT2803ISK-4.5-T1 AnalogicTech, AAT2803ISK-4.5-T1 Datasheet
![no-image](/images/no-image-200.jpg)
AAT2803ISK-4.5-T1
Available stocks
Related parts for AAT2803ISK-4.5-T1
AAT2803ISK-4.5-T1 Summary of contents
Page 1
... LED with the input voltage. AnalogicTech's AS (Advanced Simple Serial Control™) serial digital input is used to enable, disable, and set current for each LED with a 16-level logarithmic scale plus four low- current settings down to 50μ ...
Page 2
Pin Descriptions Pin # Symbol Function 1 C1- Flying capacitor 1 negative terminal. 2 C1+ Flying capacitor 1 positive terminal. Connect a 1μF capacitor between C1+ and C1-. 3 VOUT_FL Flash output voltage. Requires 1μF capacitor connected between this pin ...
Page 3
Absolute Maximum Ratings Symbol Description V Input Voltage IN V EN/SET to GND Voltage EN/SET T Operating Junction Temperature Range J T Maximum Soldering Temperature (at leads, 10 sec) LEAD Thermal Information 2 Symbol Description P Maximum Power Dissipation D ...
Page 4
Electrical Characteristics V = 3.6V OUT 1 2 Typical values are T = 25°C. A Symbol Description V Operation Range IN I Operating Current CC I Shutdown Current SHDN I I ...
Page 5
Electrical Characteristics V = 3.6V OUT 1 2 Typical values are T = 25°C. A Symbol Description T EN/SET Low Time EN/SET LO T Minimum EN/SET High Time EN/SET _ HI ...
Page 6
Typical Characteristics–Flash Driver Charge Pump Section Output Voltage vs. Output Current (V = 4.5V; EN_FL = V ; EN/SET = GND) OUT_FL IN 4.60 4.56 3.6V 4.52 4.48 3.0V 3.3V 4.44 2.7V 4.40 0.1 1.0 10.0 Output Current (mA) Start-Up ...
Page 7
Typical Characteristics–Flash Driver Charge Pump Section Output Ripple Voltage vs. Time (I = 50mA @ V = 3.5V) OUT (10mV/div) V OUT (10mV/div (10mA/div) 500ns/div Supply Current vs. Supply Voltage 3. 0μA OUT ...
Page 8
Typical Characteristics–White LED Backlight Driver Section Unless otherwise noted 3.6V Efficiency vs. Supply Voltage 100 4.1mA 10.2mA 2.8 3.0 3.2 3.4 3.6 Supply ...
Page 9
Typical Characteristics–White LED Backlight Driver Section Unless otherwise noted 3.6V Load Characteristics (V = 3.8V; 1.5X Mode; 15mA Load (40mV/div) CP (40mV/div) V SINK (40mV/div) 500ns/div Load Characteristics (V = 4.0V; 1.5X Mode; ...
Page 10
Typical Characteristics–White LED Backlight Driver Section Unless otherwise noted 3.6V vs. V LAT IN 350 300 -40°C 250 200 150 25°C 100 50 0 2.7 2.9 3.1 3.3 3.5 3.7 3.9 4.1 4.3 4.5 4.7 ...
Page 11
Functional Block Diagram EN_FL Cwire EN/SET Interface Functional Description The AAT2803 is a dual charge pump targeted for backlight and flash applications. The charge pump for white LED applications is a tri-mode load switch (1X) and ...
Page 12
Constant Current Output Level Settings The constant current sink levels for the white LED backlight (D1 to D6) are set via the serial interface according to a logarithmic scale where each code is 1dB lower than the previous code. In ...
Page 13
AS Cwire Serial Interface Timing 2 EN/SET Address Data Reg 1 Data Reg 2 AS Cwire Addressing 2 Five addresses are available to enable all of the part's functionality. Two 4-bit registers control the main and sub-channels, giving 16 settings ...
Page 14
Max Current Register Settings—Address 4 Data Max Current 1 20mA Max Scale 2 30mA Max Scale 3 15mA Max Scale 4 Low Current Mode Low Current Register Settings—Address 5 Data D1-D4 (mA ...
Page 15
Capacitor Characteristics Ceramic composition capacitors are highly recom- mended over all other types of capacitors for use with the AAT2803. Ceramic capacitors offer many advantages over their tantalum and aluminum elec- trolytic counterparts. A ceramic capacitor typically has very low ...
Page 16
... Phone (408) 737-4600 Fax (408) 737-4611 16 Six-Channel White LED Backlight Marking Part Number (Tape and Reel) 1 OFXYY QFN44-24 0.305 ± 0.075 R0.030Max 2.7 ± 0.05 Bottom View 0.214 ± 0.036 Side View Charge Pump with Flash 2 AAT2803ISK-4.5-T1 Pin 1 Identification 1 6 2803.2006.04.1.5 ...