SL2009 Zarlink Semiconductor Inc, SL2009 Datasheet
SL2009
Available stocks
Related parts for SL2009
SL2009 Summary of contents
Page 1
... Applications • Cable Network interface modules and tuners • Data communications systems Description The SL2009 is a dual IF amplifier intended for application in cable tuners, and integrates all of the IF gain and AGC required to deliver 1Vp standard tuner configuration. (12) AGC1 (11) SDRIVEIP ...
Page 2
... The SAWF amplifier also incorporates a level detect block whose output AGCOUT, can be used to control the gain of the SAWF amplifier or other gain stages in front of the SL2009. This AGC characteristic can be set "current set" resistor connected between the AGCBIAS input and Vee. The typical ...
Page 3
... Figure 3 - Typical SAWF driver stage AGC characteristic Closed Loop SAWF Driver OP vs RAGC (Vcc = 5v, 25'C) 114 112 110 108 106 104 102 100 0 1 Figure 4 - AGCOUT characteristic versus AGCBIAS resistor 2 2.5 3 AGC Voltage ( RAGC (Kohm) SL2009 4 ...
Page 4
... SL2009 CH1 CH1 PRm PRm Cor Cor Avg Avg 16 16 START START 1.000 000 MHz 1.000 000 MHz Figure 5 - Typical SAWF driver input impedance, single-ended CH1 S 11 PRm Cor Avg 16 START 1.000 000 MHz Figure 6 - Typical SAWF driver output impedance, single-ended ...
Page 5
... Figure 7 - Typical IF amplifier stage AGC characteristic IFAmp AGC Slope ( Vcc = 5v, 25' AGC Voltage (V) SL2009 ...
Page 6
... SL2009 CH1 PRm Cor Avg 16 START 1.000 000 MHz Figure 8 - Typical IF amplifier input impedance, single-ended CH1 Cor START 1.000 000 MHz Figure 9 - Typical IF amplifier output impedance, single-ended 6 8 Feb 2001 16:19: STOP 100.000 000 MH z ...
Page 7
... Table 2 - Electrical Characteristics SL2009 units Conditions mA Pin (3) VccIF and pin (16) VccSAW are isolated on chip. MHz Over specified output range. Excluding SAW filter contributions. 8MHz B/W. See note (4) k Differential, see figure ( Tamb=27˚C, referred to ...
Page 8
... SL2009 Characteristics IF amplifier Input impedance Noise Figure Variation in NF with gain adjust Output referred IP3 Gain Maximum Minimum Output impedance Output limiting AGC2 leakage current Table 2 - Electrical Characteristics (continued) Notes: (1) Two output tones at 104 dB V within operating range (2) Two output tones at 108 dB V within operating range ...
Page 9
... Package thermal resistance, chip to case Package thermal resistance, chip to ambient Power consumption at 5.25V ESD protection IF=VccSAW cc min max units -0.3 7 -0.3 Vcc+0.3 -55 150 ˚C 150 ˚C 32.2 ˚C 108.1 ˚C/W 368 Table 3 - Absolute Maximum Ratings SL2009 conditions V V Mil-std 883B method 3015 cat1 9 ...
Page 10
... AGC2 AGCout 5 12 IFOP AGC1 C11 10nF 6 11 Vee SDriveIP 7 10 IFOPB SDriveIPB C16 8 9 Vee AGCbias 470nF SL2009 C17 470nF C13 15pF L1 1uH R3 R4 R14 R15 C15 10pF 1K R17 C8 470nF 0R C7 470nF L4 AGC select 1uH R16 ...
Page 11
...
Page 12
... For more information about all Zarlink products Information relating to products and services furnished herein by Zarlink Semiconductor Inc. or its subsidiaries (collectively “Zarlink”) is believed to be reliable. However, Zarlink assumes no liability for errors that may appear in this publication, or for liability otherwise arising from the application or use of any such information, product or service or for any infringement of patents or other intellectual property rights owned by third parties which may result from such application or use ...