ISL62870 Intersil Corporation, ISL62870 Datasheet - Page 6
![no-image](/images/manufacturer_photos/0/3/342/intersil_corporation_sml.jpg)
ISL62870
Manufacturer Part Number
ISL62870
Description
PWM DC/DC Voltage Regulator Controller
Manufacturer
Intersil Corporation
Datasheet
1.ISL62870.pdf
(16 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ISL62870HRUZ-T
Manufacturer:
M/A-COM
Quantity:
45
Part Number:
ISL62870HRUZ-T
Manufacturer:
INTERSIL
Quantity:
20 000
Functional Pin Descriptions
GND (Pin 1)
IC ground for bias supply and signal reference.
EN (Pin 2)
Enable input for the IC. Pulling EN above the V
threshold voltage initializes the soft-start sequence.
NC (Pins 3, 5)
No internal connection. Pins 3 and 5 should be connected to
the GND pin.
SREF (Pin 4)
Soft-start programming capacitor input. Connects internally
to the inverting input of the V
PGOOD (Pin 6)
Power-good open-drain indicator output. This pin changes to
high impedance when the converter is able to supply
regulated voltage. The pull-down resistance between the
PGOOD pin and the GND pin identifies which protective fault
has shut down the regulator. See Table 1 on page 10.
FB (Pin 7)
Voltage feedback sense input. Connects internally to the
inverting input of the control-loop error amplifier. The
converter is in regulation when the voltage at the FB pin
equals the voltage on the SREF pin. The control loop
compensation network connects between the FB pin and the
converter output. See Figure 8 on page 10.
VO (Pin 8)
Output voltage sense input for the R
also serves as the reference input for the overcurrent
detection circuit. See Figure 5 on page 7.
OCSET (Pin 9)
Input for the overcurrent detection circuit. The overcurrent
setpoint programming resistor R
pin to the sense node. See “OVERCURRENT
PROGRAMMING CIRCUIT” on page 7.
PHASE (Pin 10)
Return current path for the UGATE high-side MOSFET
driver. VIN sense input for the R
polarity detector input. Connect to junction of output inductor,
high-side MOSFET, and low-side MOSFET. See “Application
Schematics” on page 3 (Figures 2 and 3).
UGATE (Pin 11)
High-side MOSFET gate driver output. Connect to the gate
terminal of the high-side MOSFET of the converter.
BOOT (Pin 12)
Positive input supply for the UGATE high-side MOSFET gate
driver. The BOOT pin is internally connected to the cathode
SET
6
3
OCSET
modulator. Inductor current
voltage setpoint amplifier.
3
modulator. The VO pin
connects from this
ENTHR
rising
ISL62870
R
of the Schottky boot-strap diode. Connect an MLCC
between the BOOT pin and the PHASE pin.
VCC (Pin 13)
Input for the IC bias voltage. Connect +5V to the VCC pin
and decouple with at least a 1µF MLCC to the GND pin. See
“Application Schematics” on page 3 (Figures 2 and 3).
PVCC (Pin 14)
Input for the LGATE and UGATE MOSFET driver circuits.
The PVCC pin is internally connected to the anode of the
Schottky boot-strap diode. Connect +5V to the PVCC pin
and decouple with a 10µF MLCC to the PGND pin. See
“Application Schematics” on page 3 (Figures 2 and 3).
LGATE (Pin 15)
Low-side MOSFET gate driver output. Connect to the gate
terminal of the low-side MOSFET of the converter.
PGND (Pin 16)
Return current path for the LGATE MOSFET driver. Connect
to the source of the low-side MOSFET.
Setpoint Reference Voltage
The 500mV output of the setpoint reference voltage (V
appears at the SREF pin. This signal is the output of the
current limited voltage follower that buffers an internal
500mV voltage reference (V
regulation when the voltage at the FB pin (V
V
measured relative to the GND pin, not the PGND pin.
The feedback voltage-divider network consisting of offset
resistor (R
down the converter output voltage (V
voltage V
output voltage of the converter. The voltage-divider relation
is given in Equation 1:
Where:
The value of offset resistor R
whenever the value of loop-compensation resistor R
been changed. Calculation of R
Equation 2:
V
SREF
OFS
FB
- V
- R
- R
connects from the FB pin to the converter output
connects from the FB pin to the GND pin
=
FB
FB
OFS
=
V
voltage at the SREF pin. Both of these pins are
---------------------------------------- -
V
OUT
= V
FB
is the loop-compensation feedback resistor that
V
OUT
OFS
SREF
is the voltage-scaling programming resistor that
equals V
SREF
⋅
--------------------------------- -
R
–
) and loop-compensation resistor (R
FB
V
⋅
R
SREF
R
+
OFS
FB
R
SREF
OFS
when V
REF
OFS
OFS
.) The converter is in
must be recalculated
www.DataSheet4U.com
OUT
is written as shown in
OUT
equals the desired
) such that the
FB
) equals the
August 14, 2008
FB
FB
) scale
(EQ. 2)
FN6708.0
SREF
(EQ. 1)
has
)