ISL28258 Intersil Corporation, ISL28258 Datasheet
ISL28258
Available stocks
Related parts for ISL28258
ISL28258 Summary of contents
Page 1
... This results in low frequency noise performance, which can only be found on devices with an order of magnitude higher supply current. ISL28158 and ISL28258 can be operated from one lithium cell or two Ni-Cd batteries. The input range includes both positive and negative rail. The output swings to both rails. ...
Page 2
... Large Signal Voltage Gain VOL V Maximum Output Voltage Swing OUT I Quiescent Supply Current, Enabled S,ON 2 ISL28158, ISL28258 Thermal Information (T = +25°C) A Thermal Resistance Output Short-Circuit Duration . . . . . . . . . . . . . . . . . . . . . . .Indefinite Ambient Operating Temperature Range . . . . . . . . .-40°C to +125°C Storage Temperature Range . . . . . . . . . . . . . . . . . .-65°C to +150°C Operating Junction Temperature . . . . . . . . . . . . . . . . . . . . . +125°C Pb-free reflow profile ...
Page 3
... Enable to Output Turn-on Delay Time, 10 10% V OUT Enable to Output Turn-off Delay Time, 10 10% V OUT NOTE: 1. Parts are 100% tested at +25°C. Temperature limits established by characterization and are not production tested. 3 ISL28158, ISL28258 = 2.5V Open +25°C unless otherwise specified CONDITIONS R = 10Ω ...
Page 4
... 16.3pF 10mV OUT P 10k FREQUENCY (Hz) FIGURE 5. GAIN vs FREQUENCY ISL28158, ISL28258 2.5V 499 10k 4.99k f g 10k 100k 1M 100k 10k OUT 10k ...
Page 5
... FREQUENCY (Hz) FIGURE 9. CMRR vs FREQUENCY -10 PSRR- -20 -30 -40 -50 -60 -70 -80 -90 -100 10 100 1k FREQUENCY (Hz) FIGURE 11. PSRR vs FREQUENCY ISL28158, ISL28258 2.5V 2.4V + 100k 2.4V 10k 16.3pF P-P 10k 100k ...
Page 6
... R = 10k L -0 16.3pF -0 OUT -0 100 150 200 TIME (µs) FIGURE 15. LARGE SIGNAL STEP RESPONSE 6 ISL28158, ISL28258 2.5V 10k 16.3pF 10k 100k = 10k P-P 250 300 350 400 6 V-OUT V-ENABLE ...
Page 7
... N = 1000 300 MAX 100 -100 MIN -300 -500 -700 -40 - TEMPERATURE (°C) FIGURE 22. V (SOIC PKG) vs TEMPERATURE ±2.75V + - 7 ISL28158, ISL28258 2.5V 100 (V) MIN 60 80 100 120 , V = ±2.5V - MEDIAN 60 80 100 120 = 0V Open ...
Page 8
... PKG) vs TEMPERATURE ±1. 250 N = 1000 200 150 100 50 0 -50 -40 - TEMPERATURE (°C) FIGURE 28 TEMPERATURE, V BIAS 8 ISL28158, ISL28258 2.5V Open. (Continued MEDIAN 60 80 100 120 = 0V, FIGURE 25 MEDIAN 60 80 100 120 = 0V, FIGURE 27 MAX MEDIAN MIN ...
Page 9
... OS 140 130 MAX 120 110 MEDIAN 100 90 80 MIN 70 -40 - TEMPERATURE (°C) FIGURE 34. CMRR vs TEMPERATURE ±2. ISL28158, ISL28258 2.5V Open. (Continued MAX MEDIAN MIN 60 80 100 120 , V = ±1. MAX MEDIAN MIN 60 80 100 120 , V = ±2.5 ...
Page 10
... L 190 N = 1000 180 170 160 150 140 130 120 110 100 -40 - TEMPERATURE (°C) FIGURE 40. V LOW vs TEMPERATURE, V OUT ISL28158, ISL28258 2.5V 1000 60 80 100 120 , V = ±2.5V 100k MAX 60 80 100 120 , V =±2.5V MAX MEDIAN ...
Page 11
... Pin Descriptions ISL28258 ISL28158 ISL28158 (8 Ld SOIC SOT-23 SOIC MSOP ISL28158, ISL28258 2.5V MAX 60 80 100 120 = -2.55V 10k, L PIN NAME FUNCTION NC Not connected IN- inverting input 2 (A) IN- (A) 6 (B) IN- (B) ...
Page 12
... Applications Information Introduction The ISL28158 is a single CMOS rail-to-rail input, output (RRIO) operational amplifier with an enable feature. The ISL28258 is a dual version without the enable feature. Both devices are designed to operate from single supply (2.4V to www.datasheet4u.com 5.5V) or dual supplies (±1.2V to ±2.75V). ...
Page 13
... Using Only One Channel The ISL28258 is a dual op amp. If the application only requires one channel, the user must configure the unused channel to prevent it from oscillating. The unused channel will oscillate if the input and output pins are floating. This will result in higher than expected supply currents and possible noise injection into the channel being used ...
Page 14
... B NX 0. SEATING PLANE 0. (L1 ISL28158, ISL28258 MDP0038 D SOT-23 PACKAGE FAMILY NOTES: 1. Plastic or metal protrusions of 0.25mm maximum per side are not A2 2. Plastic interlead protrusions of 0.25mm maximum per side are not A1 3. This dimension is measured at Datum Plane “ ...
Page 15
... Plastic or metal protrusions of 0.006” maximum per side are not included. 2. Plastic interlead protrusions of 0.010” maximum per side are not included. 3. Dimensions “D” and “E1” are measured at Datum Plane “H”. 4. Dimensioning and tolerancing per ASME Y14.5M-1994 15 ISL28158, ISL28258 D (N/2)+1 (N/2) e ...
Page 16
... However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 16 ISL28158, ISL28258 MDP0043 A MINI SO PACKAGE FAMILY ...