FB1209S-1W MORNSUN Science& Technology Ltd., FB1209S-1W Datasheet - Page 2

• Manufacturer Part Number: FB1209S-1W
• Description: Dual/single Output Dc-dc Converter
• Manufacturer: MORNSUN Science& Technology Ltd.

1. All specifications measured at TA=25°C, humidity<75%, nominal input voltage and rated output load
2. Dual output models unbalanced load: ±5%.
*Test ripple and noise by “parallel cable” method. See detailed operation instructions at Testing of Power
Converter section, application notes.
Note:
Requirement on output load
output load is not less than 10% of the full load, and that this product should never be
operated under no load! If the actual output power is very small, please connect a resistor
with proper resistance at the output end in parallel to increase the load, or use our company’s
products with a lower rated output power.
Item
Output power
Line regulation
Load regulation
Output voltage accuracy
Temperature drift
Ripple & Noise*
Switching frequency
OUTPUT SPECIFICATIONS
unless otherwise specified.
TYPICAL CHARACTERISTICS
OUTLINE DIMENSIONS & PIN CONNECTIONS
APPLICATION NOTE
To ensure this module can operate efficiently and reliably, During operation, the minimum
Note:
Unit:mm(inch)
Pin section: 0. 50*0.30mm(0.020*0.012inch)
Pin tolerances: 0.10mm( 0.004inch)
General tolerances: 0.25mm( 0.010inch)
MORNSUN reserves the copyright
1 2
5
Test conditions
For Vin change of 1%
10% to 100% load(5V output)
10% to 100% load (9V output)
10% to 100% load (12V output)
10% to 100% load (15V output)
100% full load
20MHz Bandwidth
6
nominal input
Full load,
Specifications subject to change without notice.
(5V input)
(others input)
FOOTPRINT DETAILS
RECOMMENDED FOOTPRINT
Top
diameter:1.00mm(0.039inch)
Pin
1
2
5
6
7
view,grid:2.54mm(0.1inch)
First A ngle Projection
Dual Output
Single Output
Ambient Temperature
Min
1
1
0.1
See tolerance envelope graph
1
1
Singles
2
2
2
2
12.8
Typ
150
250
5
5
8.3
6.8
6.3
5
5
42
6
6
Duals
7
7
7
7
Max
±1.2
0.03
200
15
15
15
15
1
(
C
)
mVp-p
Units
%/°C
KHz
W
%
EA_S-1W & FB_S-1W
Recommended testing and application circuit
ripple,
connected to the input and output ends of the
DC/DC converter, see (Figure 1).
the frequency of the “LC” filtering network should
be staggered with the DC/DC frequency to avoid
mutual interference. However, the capacitance of
the output filter capacitor must be proper. If the
capacitance is too big, a startup problem might
arise. For every channel of output, provided the
safe and reliable operation is ensured, the
greatest capacitance of its filter capacitor sees
(Table 1).
It’s not recommended to connect any external
capacitor in the application field with less than 0.5
watt output.
Output Voltage Regulation and Over-voltage
Protection Circuit
regulation,
protection is a linear voltage regulator with
overheat protection that is connected to the input
or output end in series (Figure 2).
Overload Protection
circuit of these products has no protection
against overload. The simplest method is to
connect a self-recovery fuse in series at the input
end or add a circuit breaker to the circuit.
No parallel connection or plug and play.
Dual Output
GND
Single Output
GND
If you want to further decrease the input/output
It should also be noted that the inductance and
(VDC)
The
Vin
Vin
Under normal operating conditions, the output
Vin
Dual Output
GND
Single Output
GND
EXTERNAL CAPACITOR TABLE (TABLE 1)
12
24
Vin
Vin
5
-
an
simplest
Cin
Cin
REG
REG
(uF)
Cin
4.7
2.2
1
-
“LC”
over-voltage
L
L
DC DC
DC DC
(VDC)
Single
Vout
device
12
15
(Figure 1)
filtering
5
9
(Figure 2)
DC
DC
A/1-2008
DC
DC
Cout
(uF)
10
4.7
2.2
1
for
network
and
REG
REG
REG
L
L Cout
L
(VDC)
output
Dual
Vout
Page 2 of 2
±12
±15
Cout
Cout
±5
±9
over-current
may
Cout
voltage
-Vout
(uF)
+Vout
+Vout
0V
0V
+Vo
+Vo
4.7
2.2
-Vo
0V
0V
1
1
be