PIC16LC72 Microchip Technology, PIC16LC72 Datasheet - Page 33
![no-image](/images/manufacturer_photos/0/4/439/microchip_technology_sml.jpg)
PIC16LC72
Manufacturer Part Number
PIC16LC72
Description
8-Bit CMOS Microcontrollers
Manufacturer
Microchip Technology
Datasheet
1.PIC16LC72.pdf
(124 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PIC16LC72-04/SO
Manufacturer:
Microchip Technology
Quantity:
135
Part Number:
PIC16LC72-04/SP
Manufacturer:
MIC
Quantity:
20 000
Part Number:
PIC16LC72A
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
Company:
Part Number:
PIC16LC72A-04/SO
Manufacturer:
Microchip Technology
Quantity:
5 000
Company:
Part Number:
PIC16LC72A-04I/ML
Manufacturer:
Microchip Technology
Quantity:
135
7.0
The CCP (Capture/Compare/PWM) module contains a
16-bit register which can operate as a 16-bit capture
register, as a 16-bit compare register or as a PWM
master/slave Duty Cycle register. Table 7-1 shows the
timer resources of the CCP module modes.
Capture/Compare/PWM Register1 (CCPR1) is com-
prised of two 8-bit registers: CCPR1L (low byte) and
CCPR1H (high byte). The CCP1CON register controls
the operation of CCP1. All are readable and writable.
FIGURE 7-1:
1998 Microchip Technology Inc.
bit7
bit 7-6: Unimplemented: Read as '0'
bit 5-4: CCP1X:CCP1Y: PWM Least Significant bits
bit 3-0: CCP1M3:CCP1M0: CCP1 Mode Select bits
U-0
—
CAPTURE/COMPARE/PWM
(CCP) MODULE
Capture Mode: Unused
Compare Mode: Unused
PWM Mode: These bits are the two LSbs of the PWM duty cycle. The eight MSbs are found in CCPR1L.
0000 = Capture/Compare/PWM off (resets CCP1 module)
0100 = Capture mode, every falling edge
0101 = Capture mode, every rising edge
0110 = Capture mode, every 4th rising edge
0111 = Capture mode, every 16th rising edge
1000 = Compare mode, set output on match (CCP1IF bit is set)
1001 = Compare mode, clear output on match (CCP1IF bit is set)
1010 = Compare mode, generate software interrupt on match (CCP1IF bit is set, CCP1 pin is unaffected)
1011 = Compare mode, trigger special event (CCP1IF bit is set; CCP1 resets TMR1 and starts an A/D
11xx = PWM mode
U-0
—
CCP1CON REGISTER (ADDRESS 17h)
CCP1X CCP1Y CCP1M3
R/W-0
conversion (if A/D module is enabled))
R/W-0
R/W-0
CCP1M2
Preliminary
R/W-0
CCP1M1 CCP1M0
R/W-0
Additional information on the CCP module is available
in the PICmicro™ Mid-Range MCU Reference Manual,
DS33023.
TABLE 7-1
CCP Mode
Compare
Capture
PIC16C72 Series
PWM
R/W-0
bit0
CCP MODE - TIMER
RESOURCE
R = Readable bit
W = Writable bit
U = Unimplemented bit,
- n =Value at POR reset
read as ‘0’
Timer Resource
DS39016A-page 33
Timer1
Timer1
Timer2