DS3930 Maxim Integrated Products, DS3930 Datasheet
DS3930
Available stocks
Related parts for DS3930
DS3930 Summary of contents
Page 1
... All Six Potentiometers Share a Common Low Side ♦ Potentiometers Separated into Two Groups of Three Potentiometers, Each Sharing a Common High Side Applications ♦ 2-Wire Serial Interface ♦ Wide Supply Range (2.7V to 5.5V) ♦ Eight DS3930s Can Share the Same 2-Wire Bus PART DS3930E 20 HI 0-2 ...
Page 2
Hex Nonvolatile Potentiometer with I/O and Memory ABSOLUTE MAXIMUM RATINGS Voltage on V Relative to Ground...................... -0.5V to +6.0V CC Voltage on I/O , I/O , I/O , I/O , SDA, SCL, A0, A1, and ...
Page 3
Hex Nonvolatile Potentiometer with ANALOG RESISTOR CHARACTERISTICS (V = +2.7V to +5.5V -40°C to +85°C, unless otherwise specified PARAMETER SYMBOL End-to-End Resistance Wiper Resistance Factory Default Wiper Setting Factory Default I/O Setting POT-to-POT Matching Differential Linearity ...
Page 4
Hex Nonvolatile Potentiometer with I/O and Memory AC ELECTRICAL CHARACTERISTICS (continued +2.7V to +5.5V -40°C to +85°C, unless otherwise specified PARAMETER SYMBOL Data Hold Time (Notes HD:DAT Data Setup Time ...
Page 5
Hex Nonvolatile Potentiometer with (V = 5.0V +25°C, unless otherwise specified SUPPLY CURRENT vs. TEMPERATURE 220 SDA = SCL = 200 180 160 140 120 -40 -20 ...
Page 6
Hex Nonvolatile Potentiometer with I/O and Memory PIN NAME 1 A0 Address Input. The address input pins determine the 2-wire address of the device Address Input 3 A2 Address Input 4 SDA 2-Wire Serial Data I/O. This pin ...
Page 7
... F8h FFh SDA SCL GND Figure 1. DS3930 Functional Diagram Detailed Description The DS3930 contains six NV potentiometers with 64 bytes of NV user memory (EEPROM), and four pro- grammable NV I/O pins. Figure functional dia- gram of the DS3930. EEPROM 64 BYTES OF EEPROM 8 RESERVED 8 POT0 CONTROL ...
Page 8
Hex Nonvolatile Potentiometer with I/O and Memory The I/O pins can be used as general-purpose digital I/O signals. The I/O pins have CMOS outputs with an Table 1. I/O Pin Truth Table PULLUP CTRL I/O PIN SETTING (I/O CONTROL (I/O ...
Page 9
... The DS3930 operates as a slave on the 2-wire bus. Connections to the bus are made through the open-drain I/O lines, SDA and SCL. The following I/O terminals control the 2-wire serial port: SDA, SCL, and A0 ...
Page 10
... Slave Address: This is the first byte received fol- lowing the start condition from the master device. The slave address consists of a 4-bit control code. For the DS3930, this is set as 1010 binary for read/write operations. The next bits of the slave address are the device address (A2–A0). The last bit of the slave address (R/W) defines the operation to be performed. When set to a ‘ ...
Page 11
... ADDRESS DETERMINED BY A0, A1, AND A2 MUST MATCH THE ADDRESS SET BY THE ADDRESS PINS. Figure 6. Example 2-Wire Transactions Applications Information Power Supply Decoupling To achieve the best results when using the DS3930, decouple the power supply with a 0.1µF high-quality, ceramic, surface-mount capacitor. Surface-mount com ...
Page 12
... Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. 12 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 © 2003 Maxim Integrated Products TRANSISTOR COUNT: 27,000 SUBSTRATE CONNECTED TO GROUND ...