ADSP-2186 Analog Devices, ADSP-2186 Datasheet - Page 8

• Manufacturer Part Number: ADSP-2186
• Description: DSP Microcomputer
• Manufacturer: Analog Devices

ADSP-2186
There are 8K words of memory accessible internally when the
PMOVLAY register is set to 0. When PMOVLAY is set to some-
thing other than 0, external accesses occur at addresses 0x2000
through 0x3FFF. The external address is generated as shown in
Table II.
PMOVLAY Memory
0
1
2
NOTE: Addresses 0x2000 through 0x3FFF should not be accessed when
PMOVLAY = 0.
This organization provides for two external 8K overlay segments
using only the normal 14 address bits, which allows for simple
program overlays using one of the two external segments in
place of the on-chip memory. Care must be taken in using this
overlay space in that the processor core (i.e., the sequencer)
does not take into account the PMOVLAY register value. For
example, if a loop operation is occurring on one of the external
overlays and the program changes to another external overlay or
internal memory, an incorrect loop operation could occur. In
addition, care must be taken in interrupt service routines as the
overlay registers are not automatically saved and restored on the
processor mode stack.
When Mode B = 1, booting is disabled and overlay memory is
disabled (PMOVLAY must be 0). Figure 5 shows the memory
map in this configuration.
Data Memory
The ADSP-2186 has 8160 16-bit words of internal data memory.
In addition, the ADSP-2186 allows the use of 8K external memory
overlays. Figure 6 shows the organization of the data memory.
Figure 5. Program Memory (Mode B = 1)
Internal
External
Overlay 1
External
Overlay 2
Table II. PMOVLAY Addressing
Figure 6. Data Memory
PROGRAM MEMORY
MAPPED REGISTERS
(DMOVLAY = 1, 2)
8K EXTERNAL
DATA MEMORY
RESERVED
EXTERNAL 8K
32 MEMORY–
8160 WORDS
INTERNAL
A13
Not Applicable Not Applicable
0
1
ADDRESS
ADDRESS
0x3FFF
0x2000
0x1FFF
0x0000
0x3FFF
0x3FEO
0x3FDF
0x2000
0x1FFF
0x0000
13 LSBs of Address
13 LSBs of Address
A12:0
Between 0x2000
and 0x3FFF
Between 0x2000
and 0x3FFF
–8–
There are 8160 words of memory accessible internally when the
DMOVLAY register is set to 0. When DMOVLAY is set to
something other than 0, external accesses occur at addresses
0x0000 through 0x1FFF. The external address is generated as
shown in Table III.
DMOVLAY Memory
0
1
2
This organization allows for two external 8K overlays using only
the normal 14 address bits. All internal accesses complete in one
cycle. Accesses to external memory are timed using the wait
states specified by the DWAIT register.
I/O Space (Full Memory Mode)
The ADSP-2186 supports an additional external memory space
called I/O space. This space is designed to support simple con-
nections to peripherals or to bus interface ASIC data registers.
I/O space supports 2048 locations. The lower eleven bits of the
external address bus are used; the upper three bits are unde-
fined. Two instructions were added to the core ADSP-2100
Family instruction set to read from and write to I/O memory
space. The I/O space also has four dedicated three-bit wait state
registers, IOWAIT0-3, that specify up to seven wait states to be
automatically generated for each of four regions. The wait states
act on address ranges as shown in Table IV.
Composite Memory Select (CMS)
The ADSP-2186 has a programmable memory select signal that
is useful for generating memory select signals for memories
mapped to more than one space. The CMS signal is generated
to have the same timing as each of the individual memory select
signals (PMS, DMS, BMS, IOMS), but can combine their
functionality.
Each bit in the CMSSEL register, when set, causes the CMS
signal to be asserted when the selected memory select is as-
serted. For example, to use a 32K word memory to act as both
program and data memory, set the PMS and DMS bits in the
CMSSEL register and use the CMS pin to drive the chip select
of the memory and use either DMS or PMS as the additional
address bit.
The CMS pin functions as the other memory select signals, with
the same timing and bus request logic. A 1 in the enable bit
causes the assertion of the CMS signal at the same time as the
selected memory select signal. All enable bits, except the BMS
bit, default to 1 at reset.
Address Range
0x000–0x1FF
0x200–0x3FF
0x400–0x5FF
0x600–0x7FF
Internal
External
Overlay 1
External
Overlay 2
Table III. Addressing
A13
Not Applicable Not Applicable
0
1
Table IV.
Wait State Register
IOWAIT0
IOWAIT1
IOWAIT2
IOWAIT3
A12:0
13 LSBs of Address
Between 0x0000
and 0x1FFF
13 LSBs of Address
Between 0x0000
and 0x1FFF
REV. A