MAX9755 Maxim Integrated Products, MAX9755 Datasheet - Page 12
![no-image](/images/manufacturer_photos/0/4/417/maxim_integrated_products_sml.jpg)
MAX9755
Manufacturer Part Number
MAX9755
Description
2.6W Stereo Audio Power Amplifiers and DirectDrive Headphone Amplifiers
Manufacturer
Maxim Integrated Products
Datasheet
1.MAX9755.pdf
(30 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
MAX9755E
Manufacturer:
MAXIM
Quantity:
35
Company:
Part Number:
MAX9755ETI
Manufacturer:
MAXIM
Quantity:
1 897
Part Number:
MAX9755ETI+T
Manufacturer:
MAXIM/美信
Quantity:
20 000
2.6W Stereo Audio Power Amplifiers and
DirectDrive Headphone Amplifiers
significant amount of DC current flows to the headphone,
resulting in unnecessary power dissipation and possible
damage to both headphone and headphone amplifier.
Maxim’s patented DirectDrive architecture uses a charge
pump to create an internal negative supply voltage. This
allows the MAX9750/MAX9751/MAX9755 headphone
amplifier output to be biased about GND, almost dou-
bling the dynamic range while operating from a single
supply. With no DC component, there is no need for the
large DC-blocking capacitors. Instead of two large
capacitors (220µF typ), the MAX9750/MAX9751/
MAX9755 charge pump requires only two small ceramic
capacitors (1µF typ), conserving board space, reducing
cost, and improving the frequency response of the head-
phone amplifier. See the Output Power vs. Charge-Pump
Capacitance and Load Resistance graph in the Typical
Operating Characteristics for details of the possible
capacitor values.
Previous attempts to eliminate the output coupling
capacitors involved biasing the headphone return
(sleeve) to the DC bias voltage of the headphone
amplifiers. This method raised some issues:
1) The sleeve is typically grounded to the chassis. Using
2) During an ESD strike, the amplifier’s ESD structures
3) When using the headphone jack as a lineout to other
In addition to the cost and size disadvantages, the DC-
blocking capacitors limit the low-frequency response of
the amplifier and distort the audio signal:
1) The impedance of the headphone load to the DC-
12
this biasing approach, the sleeve must be isolated
from system ground, complicating product design.
are the only path to system ground. The amplifier
must be able to withstand the full ESD strike.
equipment, the bias voltage on the sleeve may con-
flict with the ground potential from other equipment,
resulting in large ground-loop current and possible
damage to the amplifiers.
blocking capacitor forms a highpass filter with the
-3dB point determined by:
where R
C
The highpass filter is required by conventional sin-
gle-ended, single-supply headphone amplifiers to
block the midrail DC component of the audio signal
from the headphones. Depending on the -3dB point,
OUT
______________________________________________________________________________________
is the value of the DC-blocking capacitor.
L
is the impedance of the headphone and
f
−
3
dB
=
2π
Low-Frequency Response
R C
L OUT
1
2) The voltage coefficient of the capacitor, the change
The combination of low-frequency attenuation and fre-
quency-dependent distortion compromises audio
reproduction. DirectDrive improves low-frequency
reproduction in portable audio equipment that empha-
sizes low-frequency effects such as multimedia lap-
tops, and MP3, CD, and DVD players.
The MAX9750/MAX9751/MAX9755 feature a low-noise
charge pump. The 550kHz switching frequency is well
beyond the audio range, and does not interfere with the
audio signals. The switch drivers feature a controlled
switching speed that minimizes noise generated by turn-
on and turn-off transients. Limiting the switching speed of
the charge pump minimizes the di/dt noise caused by the
Figure 3. Low-Frequency Attenuation of Common DC-Blocking
Capacitor Values
the filter can attenuate low-frequency signals within
the audio band. Larger values of C
attenuation but are physically larger, more expen-
sive capacitors. Figure 3 shows the relationship
between the size of C
quency attenuation. Note that the -3dB point for a
16Ω headphone with a 100µF blocking capacitor is
100Hz, well within the audio band.
in capacitance due to a change in the voltage
across the capacitor, distorts the audio signal. At
frequencies around the -3dB point, the reactance of
the capacitor dominates, and the voltage coefficient
appears as frequency-dependent distortion. Figure
4 shows the THD+N introduced by two different
capacitor dielectrics. Note that around the -3dB
point, THD+N increases dramatically.
-12
-15
-18
-21
-24
-27
-30
-3
-6
-9
0
10
LOW-FREQUENCY ROLLOFF
100
FREQUENCY (Hz)
33µF
OUT
(R
100µF
L
220µF
= 16Ω)
1k
330µF
and the resulting low-fre-
DirectDrive
www.DataSheet4U.com
10k
OUT
Charge Pump
100k
reduce the