MAX803 Maxim, MAX803 Datasheet - Page 6
![no-image](/images/no-image-200.jpg)
MAX803
Manufacturer Part Number
MAX803
Description
3-Pin Microprocessor Reset Circuits
Manufacturer
Maxim
Datasheet
1.MAX803.pdf
(8 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
MAX803JEXR+T
Manufacturer:
MAXIM/美信
Quantity:
20 000
Company:
Part Number:
MAX803LEXR+T
Manufacturer:
MAXIM
Quantity:
982
Part Number:
MAX803LEXR+T
Manufacturer:
MAXIM/美信
Quantity:
20 000
Part Number:
MAX803MEXR+T
Manufacturer:
MAXIM/美信
Quantity:
20 000
Part Number:
MAX803R/S/T
Manufacturer:
MAXIM/美信
Quantity:
20 000
Company:
Part Number:
MAX803REXR
Manufacturer:
MAXIM
Quantity:
42 000
Part Number:
MAX803REXR+T
Manufacturer:
MAXIM/美信
Quantity:
20 000
Company:
Part Number:
MAX803SEXR+
Manufacturer:
Maxim
Quantity:
42
Company:
Part Number:
MAX803SEXR+T
Manufacturer:
MAXIM
Quantity:
11 500
Company:
Part Number:
MAX803SQ120T1G
Manufacturer:
ON Semiconductor
Quantity:
2 200
ground, holding RESET low (Figure 2). R1’s value is not
critical; 100kΩ is large enough not to load RESET and
small enough to pull RESET to ground.
A 100kΩ pull-up resistor to V
for the MAX810 if RESET is required to remain valid for
V
Since the RESET output on the MAX803 is open drain,
this device interfaces easily with µPs that have bidirec-
tional reset pins, such as the Motorola 68HC11.
Connecting the µP supervisor’s RESET output directly
to the microcontroller’s (µC’s) RESET pin with a single
pull-up resistor allows either device to assert reset
(Figure 3).
Generally, the pull-up connected to the MAX803 will
connect to the supply voltage that is being monitored at
the IC’s V
open-drain output to level-shift from the monitored sup-
ply to reset circuitry powered by some other supply
(Figure 4). Note that as the MAX803’s V
below 1V, so does the IC’s ability to sink current at
RESET. Also, with any pull-up, RESET will be pulled
high as V
occurs depends on the pull-up resistor value and the
voltage to which it is connected.
3-Pin Microprocessor Reset Circuits
Figure 3. Interfacing to µPs with Bidirectional Reset I/O
6
CC
V
_______________________________________________________________________________________
CC
< 1V.
CC
CC
MAX803 Open-Drain RESET Output
MAX803
Allows Use with Multiple Supplies
GND
V
CC
pin. However, some systems may use the
decays toward 0. The voltage where this
RESET
Bidirectional Reset Pins
Interfacing to µPs with
CC
is also recommended
RESET
INPUT
MOTOROLA
68HCXX
CC
GND
V
µP
CC
decreases
Most µP supervisor ICs have reset threshold voltages
between 5% and 10% below the value of nominal sup-
ply voltages. This ensures a reset will not occur within
5% of the nominal supply, but will occur when the sup-
ply is 10% below nominal.
When using ICs rated at only the nominal supply ±5%,
this leaves a zone of uncertainty where the supply is
between 5% and 10% low, and where the reset may or
may not be asserted.
The MAX8_ _L/T/Z use highly accurate circuitry to
ensure that reset is asserted close to the 5% limit, and
long before the supply has declined to 10% below
nominal.
Figure 4. MAX803 Open-Drain RESET Output Allows Use with
Multiple Supplies
___________________Chip Information
TRANSISTOR COUNT: 275 (SOT23)
MAX803
+3.3V
GND
V
CC
RESET
Benefits of Highly Accurate
380 (SC70)
R
PULLUP
Reset Threshold
RESET
INPUT
5V SYSTEM
+5.0V
GND
V
CC